Built 4v motor ported heads, Factory cobra blowerdrive, Kooks , Stainless works Bremb

[carolinacat]

Motor has never been ran. It is a Houston Performance 302. Eagle rods, Je pistons, cobra 4v heads, Ported, Upgraded Crower valve springs, Titanium retainers, have 9 thread spark plug threads, Custom Ground cams big lift big duration, new Ford oil pump, Best I remember 9:1comp and 1000hp capable


Oil pan to valve covers long block $6950

Canton road race oil pan has baffles with trap doors in it. It looks used but its just been mounted to motor sitting. And i have the windage tray also. both for 300 shipped

Kooks stainless headers 1 7/8 to 3 inch will fit a 4v in a foxbody $800

have a t56, clutch, mgw shifter, fore fuel rails, injectors, chiselded ic tank, meizer pump Cobra wiring harnesses, computer, stainless works exhaust 114inch brembo brakes etc.

 

[fs308]

can you email/PM me pics of the headers installed?

 

[2001Cobra8.1]

how much for the pulley system, heat exchanger, alt, and intercooler with piping?

 

[svt4me38]

Pics and price on brembos to [email protected]

 

[Carbon Driven]

I'll take the heads if you will part it, (no valve covers needed) how much?

 

[twisted03snake]

Built 4v motor ported heads, Factory cobra blowerdrive, Kooks , Stainless wor...

..

 

[pickup_man06]

I'll take the heads if you will part it, (no valve covers needed) how much?

He won't part it, I've already tried

 

[carolinacat]

can you email/PM me pics of the headers installed?

Don't think I have any Ill look tonight. They are tight but they fit. I had to notch a little on a mm k member on the bottom right rear where it bolted to the car. With the Anthony jones they went right in.

how much for the pulley system, heat exchanger, alt, and intercooler with piping?

That pic I have is all the parts I have I don't have a heat exchanger. want 1300 for what I have in the pic.

Pics and price on brembos to [email protected]

Go to venom technologies website to see a pic. I have black calipers solid rotors. They are in a box they haven't been taken out. If your dead serious about them ill open the box to take pics.

I'll take the heads if you will part it, (no valve covers needed) how much?

Im not against parting the motor Id rather not have to but if there was enough intrest I would possibly do it. I have some interested parties in the complete motor. That is the way I would like to sell it.

 

[kjfoley04]

What color handle on MGW shifter? also what size are the injectors?

 

[carolinacat]

red and blue and 72# injectors

 

[2003DSGMACH1]

I sent you a PM about the eaton parts.

 

[Carbon Driven]

Don't think I have any Ill look tonight. They are tight but they fit. I had to notch a little on a mm k member on the bottom right rear where it bolted to the car. With the Anthony jones they went right in.

That pic I have is all the parts I have I don't have a heat exchanger. want 1300 for what I have in the pic.


Go to venom technologies website to see a pic. I have black calipers solid rotors. They are in a box they haven't been taken out. If your dead serious about them ill open the box to take pics.



Im not against parting the motor Id rather not have to but if there was enough intrest I would possibly do it. I have some interested parties in the complete motor. That is the way I would like to sell it.

Ok cool I understand but if you decide to part it hit me up for the heads. Thanks

 

[82dawgcrazy]

Hi, I am interested in engine and supercharger parts. Please e-mail the engine build sheet to [email protected].

Also, where are you located? I am through NC often and would prefer to
pick up if you are in central or western NC. Thanks.

 

[carolinacat]

pm and emails sent/replied to. There have been alot of PMs so if i missed you please try again.

 

[Pritch]

Go to venom technologies website to see a pic. I have black calipers solid rotors. They are in a box they haven't been taken out. If your dead serious about them ill open the box to take pics.

Are these 05+ 14" Brembos or direct fit for the 94-04?

 

[carolinacat]

They are 04 down ones.

 

[4vpower]

Do these heads have timsert inserts installed to make them 9 thread heads ?. By looking at your pictures you have early casting heads which have 4 thread holes

 

[carolinacat]

Full Torque/Lock-N-Stitch has aluminum insert then a alumiumd dowel that goes thru so they cant ever come out good shit.

 

[nucworker]

cams

Interested in the cams if you part it.

Let me know.

Patrick

 

[carolinacat]

People that are interested in parts of the long block pm me what your offering then i can keep up with who's offering what.