Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
New Edge Cobras
Are 99/01 lower intakes the same as Mach 1's?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Nazman" data-source="post: 2536359" data-attributes="member: 986"><p>Ok,</p><p></p><p>Same part number, same design and all but very diferent in the inside.</p><p></p><p>Well, based on my limited experince with these intakes (I have ported o/a 18-20 of them). The 03-04 Mach intakes are extremly clean castings, therefore much easier to work with and they "should" flow a bit better than the 99-01s specially the 99s!</p><p></p><p>This is the way I see it:</p><p></p><p>99 Pre-Fix = BAD! (I'll not touch them, way too much flash/junk all around)</p><p>99 Fixed (Blue Dot) = Extrude Hone, runners are cleaned but still have a bit of flash at the very entrance of the runners, the feeder ports needs lots of work.</p><p>99 Fixed (Green Dot) = Acid "ported"/cleaned, about as good as the Blue Dot, may be the Blue dot a bit better. Needs some work on the feeder ports as well.</p><p>01 Green Dot = Much improved over the 99 version, about as good as the 03-04 Mach 1s. </p><p>03-04 Mach 1 = Best version, very clean.</p><p></p><p>Of the shell, the 03-04 Mach intakes should out perform the 99-01 versions but after porting they should flow o/a same numbers. </p><p></p><p>Again, this is my uneducated comment and just based on what I have seen.</p><p></p><p>Naz</p></blockquote><p></p>
[QUOTE="Nazman, post: 2536359, member: 986"] Ok, Same part number, same design and all but very diferent in the inside. Well, based on my limited experince with these intakes (I have ported o/a 18-20 of them). The 03-04 Mach intakes are extremly clean castings, therefore much easier to work with and they "should" flow a bit better than the 99-01s specially the 99s! This is the way I see it: 99 Pre-Fix = BAD! (I'll not touch them, way too much flash/junk all around) 99 Fixed (Blue Dot) = Extrude Hone, runners are cleaned but still have a bit of flash at the very entrance of the runners, the feeder ports needs lots of work. 99 Fixed (Green Dot) = Acid "ported"/cleaned, about as good as the Blue Dot, may be the Blue dot a bit better. Needs some work on the feeder ports as well. 01 Green Dot = Much improved over the 99 version, about as good as the 03-04 Mach 1s. 03-04 Mach 1 = Best version, very clean. Of the shell, the 03-04 Mach intakes should out perform the 99-01 versions but after porting they should flow o/a same numbers. Again, this is my uneducated comment and just based on what I have seen. Naz [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
New Edge Cobras
Are 99/01 lower intakes the same as Mach 1's?
Top