Long Island NY
Looking to get rid of all my modular ford stuff. I have a LOT!!! lol
Have plenty not listed below such as 2v/4v heads, 5.4 iron blocks and 4.6 cores. I can ship blocks to your local fastenal on a skid. Buyer pays shipping
Aluminum 4.6 block
- Professionally machined
- Line honed w/arp studs
- Honed w/deck plate & studs
- Block was square decked
- Bores are .020, ran for 2 seasons and just had it freshly honed & wash. Ready to assemble
- Includes arp side bolts and head & main studs
$1250
Standard bore TESKID block, super low
Miles, never been machined, not burnt or blown up. Just got a light hone done and cylinders look beautiful!!! $800
Can provide arp studs for heads/mains from my other teskid block for $1000 total
Used .020 TESKID block. Needs to go .030 over or send it out for a big bore sleeve build. Has arp main studs. Cylinders have some scoring
$650, $400 with no arp hardware.
Eagle 5.0 4340 stroker crank & rods. Was just cut & polished. Std mains, rods cut .010. Hasn’t been run yet. Includes matching eagle H beam rods, 6 are perfect. 2 rods need to be reconditioned or replaced. This is a 6” rod combo Pistons are junk but come with it. $750 crank & rods, plus shipping
Beautiful set of DSS 4.6 dished 4v pistons, hardly any run time, no wear on skirts. They are on H beam rods w/arp 2000 bolts. They have brand new rings and rod bearings installed, I was ready to put these in a motor but changed directions. Ready to drop in your standard bore 4.6 block. This package is over $1,500 from dss.
$1250 plus shipping
Nice used H beam stroker rods w/arp 2000 bolts, .020 over 4v pistons included but are heavily used. $650
Complete built 4.6 long block. Valve covers to pan. Aluminum block, arp studs, Cobra crank, Manley H beam rods, Diamond pistons. Stage 3 Cnc ported heads, nitrous cams & springs. Motor still runs but has low compression in cylinder 5. Piston is intact when I went in with camera. Believe to be an issue with intake valve. I’d suggest you freshen the motor. Lots of money invested, built a few years ago. $2500 for whole motor. Can ship to your local fastenal on a pallet
Original Bullitt 4.6 2v intake setup. Ported and polished, comes complete with C&L cold air intake, bullit throttle cable, stock throttle body, 39LB injectors & fuel rails. I’d like to sell it with the complete nitrous system at this time. Has nitrous outlet plate kit, purge kit,bottle w/bracket and bottle warmer, includes lines, rpm/window switch for activation, nos mini controller. Will also include nitrous switch panel that goes in the cupholder. This is a complete setup and everything you need to run the nitrous on a modular ford. $2000 for the entire setup. Shipping available. Can also sell ecu & sct tuner with custom tunes for this setup.
Complete built 4r70w transmission swap
Recently freshened, still in car can demo.
4r70w stage 3
Forged drum, kevlar bands, Lentech full manual shift valve body with trans brake
Fwd shift pattern 3 speed w o/d
Custom protorque converter
B&m ratchet Shifter
O/d on toggle switch
Deep aluminum pan
Trans cooler w custom steel braided line
Crossmember & mount
Aluminum driveshaft
This will include everything you need to swap into your modular powered ford.
$3250
New Fore return style fuel system. Twin in tank pumps, new cobra tank, includes pump controller, lines, filters, and Regulator. Been in the car less then 3 months. $1500
Mach 1 front seats. Great shape. $850
2v Mac long tube headers & Catless x pipe $650
Bassani stainless cat back. With or without tailpipes. $400
Sent from my iPhone using Tapatalk
Looking to get rid of all my modular ford stuff. I have a LOT!!! lol
Have plenty not listed below such as 2v/4v heads, 5.4 iron blocks and 4.6 cores. I can ship blocks to your local fastenal on a skid. Buyer pays shipping
Aluminum 4.6 block
- Professionally machined
- Line honed w/arp studs
- Honed w/deck plate & studs
- Block was square decked
- Bores are .020, ran for 2 seasons and just had it freshly honed & wash. Ready to assemble
- Includes arp side bolts and head & main studs
$1250
Standard bore TESKID block, super low
Miles, never been machined, not burnt or blown up. Just got a light hone done and cylinders look beautiful!!! $800
Can provide arp studs for heads/mains from my other teskid block for $1000 total
Used .020 TESKID block. Needs to go .030 over or send it out for a big bore sleeve build. Has arp main studs. Cylinders have some scoring
$650, $400 with no arp hardware.
Eagle 5.0 4340 stroker crank & rods. Was just cut & polished. Std mains, rods cut .010. Hasn’t been run yet. Includes matching eagle H beam rods, 6 are perfect. 2 rods need to be reconditioned or replaced. This is a 6” rod combo Pistons are junk but come with it. $750 crank & rods, plus shipping
Beautiful set of DSS 4.6 dished 4v pistons, hardly any run time, no wear on skirts. They are on H beam rods w/arp 2000 bolts. They have brand new rings and rod bearings installed, I was ready to put these in a motor but changed directions. Ready to drop in your standard bore 4.6 block. This package is over $1,500 from dss.
$1250 plus shipping
Nice used H beam stroker rods w/arp 2000 bolts, .020 over 4v pistons included but are heavily used. $650
Complete built 4.6 long block. Valve covers to pan. Aluminum block, arp studs, Cobra crank, Manley H beam rods, Diamond pistons. Stage 3 Cnc ported heads, nitrous cams & springs. Motor still runs but has low compression in cylinder 5. Piston is intact when I went in with camera. Believe to be an issue with intake valve. I’d suggest you freshen the motor. Lots of money invested, built a few years ago. $2500 for whole motor. Can ship to your local fastenal on a pallet
Original Bullitt 4.6 2v intake setup. Ported and polished, comes complete with C&L cold air intake, bullit throttle cable, stock throttle body, 39LB injectors & fuel rails. I’d like to sell it with the complete nitrous system at this time. Has nitrous outlet plate kit, purge kit,bottle w/bracket and bottle warmer, includes lines, rpm/window switch for activation, nos mini controller. Will also include nitrous switch panel that goes in the cupholder. This is a complete setup and everything you need to run the nitrous on a modular ford. $2000 for the entire setup. Shipping available. Can also sell ecu & sct tuner with custom tunes for this setup.
Complete built 4r70w transmission swap
Recently freshened, still in car can demo.
4r70w stage 3
Forged drum, kevlar bands, Lentech full manual shift valve body with trans brake
Fwd shift pattern 3 speed w o/d
Custom protorque converter
B&m ratchet Shifter
O/d on toggle switch
Deep aluminum pan
Trans cooler w custom steel braided line
Crossmember & mount
Aluminum driveshaft
This will include everything you need to swap into your modular powered ford.
$3250
New Fore return style fuel system. Twin in tank pumps, new cobra tank, includes pump controller, lines, filters, and Regulator. Been in the car less then 3 months. $1500
Mach 1 front seats. Great shape. $850
2v Mac long tube headers & Catless x pipe $650
Bassani stainless cat back. With or without tailpipes. $400
Sent from my iPhone using Tapatalk