347 Short block
Fresh machined stock block from Fordstrokers.com
DSS rotating assembly; cast crank, I beam rods, & upgraded X series pistons
Fully balanced & blueprinted to 28oz imbalance. Fresh rings
Milodon 7qt oil pan
HV oil pump
DSS main girdle & windage tray.
Rotating assembly has about 700 miles on it & was just swapped from an early block to a late model block from Fordstrokers.
Old school TFS KPI High Ports complete w/ valves, springs, & JBA shaft mount 1.7 RRs. machined for Fel Pro loc-wire gaskets, fresh 3 angle valve job and new springs, new Ti retainers & locks
Jay Allen Custom Hyd. roller, never ran
Comp retrofit hyd roller lifters, new never ra
Ford racing damper, used good condition 28oz balance
TFS R intake w/ polished upper 75mm TB opening
MSD Pro Billet Dizzy, 700 miles of use
Black ford racing tall valve covers
Accufab 75mm race TB, new
CSR Billet aluminum elect water pump, polished finish
Dog ringed G-force T5 w/ 26 spline input & Steeda tri ax shifter
Alum driveshaft
alum race radiator
38lb injectors
Mac 1.75" Ceramic coated LT headers
130 amp altenator
Brand new Promotion Powertrain custom DF clutch assembly
Brand new F1 Racing lightened chromoly flywheel
Moroso header evac system installed
chassis:
A 65,000 original mile two owner car
wheels/ tires weld drag lites, bigs & littles 26x10 et streets on rear
Accel DFI w/ wideband 02 kit
MSD HVC U coil
switch panel
UPR K-member, A-arms, Coil over w/ 12" 130lb springs
Tokico Illuma 5 way adjustable shocks & struts
Skinny kid race cars manual brake kit
SSBC Big bite cross drilled and slotted disc brakes at all 4 corners
SVO 73mm front calipers w/ steel bushings all calipers powder coated Red
Flaming River manual steering rack & steering knuckle
Momo steering wheel
Saleen instrument cluster
Monster Tach
Steeda billet alum weight jacker LCA's
Steeda double adj. UCAs
31 spline moser axles
Detroit Tru-trac w/ FMS 4.10 gears
ARP studs on bearing carrier
ARP wheel studs
TA alum rear end Girdle
Driveshaft Safety loop
Steeda FLSFCs w/ torque box re-inforcements
Steeda rear sport springs
Upper torque box re-inforcements
welded torque boxes
8 point MS cage
Optima red top battery trunk mounted w/ box
standard gas tank w/ 255lph in tank pump
Aeromotive fuel pressure regulator
smoothed engine bay, all wiring tucked behind fenders
Steeda billet alum CC plates
New weather stripping throughout
3" fiberglass cowl hood
Baseline ARB
MSD 6AL
Hurst line loc
Kirkey aluminum drag seats
4 point harnesses
Donavan racing chromoly bumper supports front & rear
solid motor mounts
spherical bushings in the diff
solid & delrin bushings in the control arms
I'm sure I'm forgetting some stuff but that's basically what is on the car now and how i would like to let it go
All of the parts listed above are in excellent condition and i bought 90% them new. some have around 700 miles of usage on them and a few track passes & others are brand new never ran. the coil, MSD 6AL, & DFI are mounted under the dash. The interior is gutted, no carpet, panels, center console, etc. No a/c or heating stuff. the car should weigh out at around 2800lbs or possibly less.
$9,000 obo
The car can be seen at Southern Speed in Tupelo, MS. I am having some suspension work and some other odd & end work done there. The car will be complete and ready race around mid august. It should go low to mid 11s on motor. The motor was put together with the intentions of putting a small shot of spray on it but never got around to installing a kit. I built the chassis to go into the 9s
I have a ton of other stuff that will go with the car but can't remember it all off the top of my head. I am offshore at the moment. Feel free to email me [email protected]. I'm only selling due to a family crisis. I have receipts for over $20,000 in parts and labor
Thanks,
Beau
Some of the spare parts that I have are:
Custom Ci TLSR cam w/ springs BNIB
Lunati solid roller lifters, used
Strange 33 spline spool, used
2 sets of skinny tires, used
aluminum radiator and fan, used
prothane motor mounts, used 700 miles or so
12" 150lb coil over springs, new
Firecore 50 plug wires, BNIB
stock 5.0 oil pan
stock brakes
stock rear sway bar
& other misc. items all will go with the car. Completely selling out please email me with questions or offers
[email protected]
Fresh machined stock block from Fordstrokers.com
DSS rotating assembly; cast crank, I beam rods, & upgraded X series pistons
Fully balanced & blueprinted to 28oz imbalance. Fresh rings
Milodon 7qt oil pan
HV oil pump
DSS main girdle & windage tray.
Rotating assembly has about 700 miles on it & was just swapped from an early block to a late model block from Fordstrokers.
Old school TFS KPI High Ports complete w/ valves, springs, & JBA shaft mount 1.7 RRs. machined for Fel Pro loc-wire gaskets, fresh 3 angle valve job and new springs, new Ti retainers & locks
Jay Allen Custom Hyd. roller, never ran
Comp retrofit hyd roller lifters, new never ra
Ford racing damper, used good condition 28oz balance
TFS R intake w/ polished upper 75mm TB opening
MSD Pro Billet Dizzy, 700 miles of use
Black ford racing tall valve covers
Accufab 75mm race TB, new
CSR Billet aluminum elect water pump, polished finish
Dog ringed G-force T5 w/ 26 spline input & Steeda tri ax shifter
Alum driveshaft
alum race radiator
38lb injectors
Mac 1.75" Ceramic coated LT headers
130 amp altenator
Brand new Promotion Powertrain custom DF clutch assembly
Brand new F1 Racing lightened chromoly flywheel
Moroso header evac system installed
chassis:
A 65,000 original mile two owner car
wheels/ tires weld drag lites, bigs & littles 26x10 et streets on rear
Accel DFI w/ wideband 02 kit
MSD HVC U coil
switch panel
UPR K-member, A-arms, Coil over w/ 12" 130lb springs
Tokico Illuma 5 way adjustable shocks & struts
Skinny kid race cars manual brake kit
SSBC Big bite cross drilled and slotted disc brakes at all 4 corners
SVO 73mm front calipers w/ steel bushings all calipers powder coated Red
Flaming River manual steering rack & steering knuckle
Momo steering wheel
Saleen instrument cluster
Monster Tach
Steeda billet alum weight jacker LCA's
Steeda double adj. UCAs
31 spline moser axles
Detroit Tru-trac w/ FMS 4.10 gears
ARP studs on bearing carrier
ARP wheel studs
TA alum rear end Girdle
Driveshaft Safety loop
Steeda FLSFCs w/ torque box re-inforcements
Steeda rear sport springs
Upper torque box re-inforcements
welded torque boxes
8 point MS cage
Optima red top battery trunk mounted w/ box
standard gas tank w/ 255lph in tank pump
Aeromotive fuel pressure regulator
smoothed engine bay, all wiring tucked behind fenders
Steeda billet alum CC plates
New weather stripping throughout
3" fiberglass cowl hood
Baseline ARB
MSD 6AL
Hurst line loc
Kirkey aluminum drag seats
4 point harnesses
Donavan racing chromoly bumper supports front & rear
solid motor mounts
spherical bushings in the diff
solid & delrin bushings in the control arms
I'm sure I'm forgetting some stuff but that's basically what is on the car now and how i would like to let it go
All of the parts listed above are in excellent condition and i bought 90% them new. some have around 700 miles of usage on them and a few track passes & others are brand new never ran. the coil, MSD 6AL, & DFI are mounted under the dash. The interior is gutted, no carpet, panels, center console, etc. No a/c or heating stuff. the car should weigh out at around 2800lbs or possibly less.
$9,000 obo
The car can be seen at Southern Speed in Tupelo, MS. I am having some suspension work and some other odd & end work done there. The car will be complete and ready race around mid august. It should go low to mid 11s on motor. The motor was put together with the intentions of putting a small shot of spray on it but never got around to installing a kit. I built the chassis to go into the 9s
I have a ton of other stuff that will go with the car but can't remember it all off the top of my head. I am offshore at the moment. Feel free to email me [email protected]. I'm only selling due to a family crisis. I have receipts for over $20,000 in parts and labor
Thanks,
Beau
Some of the spare parts that I have are:
Custom Ci TLSR cam w/ springs BNIB
Lunati solid roller lifters, used
Strange 33 spline spool, used
2 sets of skinny tires, used
aluminum radiator and fan, used
prothane motor mounts, used 700 miles or so
12" 150lb coil over springs, new
Firecore 50 plug wires, BNIB
stock 5.0 oil pan
stock brakes
stock rear sway bar
& other misc. items all will go with the car. Completely selling out please email me with questions or offers
[email protected]
Last edited:
