Built by Professional engine builder and NMRA champ Rich Groh of RGR Engines in IL.
have a huge binder of every major receipt. bought the car bone stock in 2002.
built 331c.i. using a r-302 4 bolt block. scat 4340 crank, forged ross pistons for t.w. heads, h-beam rods
arp studs and bolts throughout entire motor
billet timing chain
anderson b-451 cam
60 lbs inj
bbrc fuel rail
glenns sleeper fuel system
t.w. heads
holley intake
t.w. tall valve covers with breathers and baffles
v1 s-trim
aftermarket blow off valve
3.33"(not installed) and 3.80" pulley
tko 500 trans
fidanza flywheel
msd digital 7
msd pro billet distr.
msd hvac II COIL
taylor battery relocation kit w/ switch in trunk
mega bite uppers and adjustable lowers
ebaich drag launch kit with airbag
springs cut 1 1/2 coil in rear
kenny brown extreme subframe kit welded jacking rails, matrix brace, super subs
3rd gen pms with 3 bar map sensor (not connected anymore but still in car and goes with it)
aluminum driveshaft
anderson switch for fan and water pump in ashtray
lakewood saftey loop
boost, volts, water temp, fuel pressure and oil pressure guages
electric fan
csr electric water pump
aluminum radiator
race mini starter
bassani short tube 1 3/4 headers
bbk h-pipe
flowmasters w/dumps
5 lug conversion
strange 31 spline axles, c-clip eliminators
auburn pro diff
lakewood 90/10
lakewood 50/50
pmas 80mm
accufab 75mm race t.b.
flaming river maual rack 15:1 ratio
aem stage 2 meth kit hooked up but never used yet(will have to tune for use)
new oem carpet
needs oil pan gasket...starting to leak by rear main
hood has one imperfection cause it flew up, but nothing noticable
missing a molding behind drivers front wheel
im probably missing a lot so just email or call with questions
philip 630-674-0331
[email protected]
new z06 coming 15k firm
have a huge binder of every major receipt. bought the car bone stock in 2002.
built 331c.i. using a r-302 4 bolt block. scat 4340 crank, forged ross pistons for t.w. heads, h-beam rods
arp studs and bolts throughout entire motor
billet timing chain
anderson b-451 cam
60 lbs inj
bbrc fuel rail
glenns sleeper fuel system
t.w. heads
holley intake
t.w. tall valve covers with breathers and baffles
v1 s-trim
aftermarket blow off valve
3.33"(not installed) and 3.80" pulley
tko 500 trans
fidanza flywheel
msd digital 7
msd pro billet distr.
msd hvac II COIL
taylor battery relocation kit w/ switch in trunk
mega bite uppers and adjustable lowers
ebaich drag launch kit with airbag
springs cut 1 1/2 coil in rear
kenny brown extreme subframe kit welded jacking rails, matrix brace, super subs
3rd gen pms with 3 bar map sensor (not connected anymore but still in car and goes with it)
aluminum driveshaft
anderson switch for fan and water pump in ashtray
lakewood saftey loop
boost, volts, water temp, fuel pressure and oil pressure guages
electric fan
csr electric water pump
aluminum radiator
race mini starter
bassani short tube 1 3/4 headers
bbk h-pipe
flowmasters w/dumps
5 lug conversion
strange 31 spline axles, c-clip eliminators
auburn pro diff
lakewood 90/10
lakewood 50/50
pmas 80mm
accufab 75mm race t.b.
flaming river maual rack 15:1 ratio
aem stage 2 meth kit hooked up but never used yet(will have to tune for use)
new oem carpet
needs oil pan gasket...starting to leak by rear main
hood has one imperfection cause it flew up, but nothing noticable
missing a molding behind drivers front wheel
im probably missing a lot so just email or call with questions
philip 630-674-0331
[email protected]
new z06 coming 15k firm
Last edited: