I have a meeting set up at my SVT dealership next Monday with the service manager, general manager and their dumb-smart-ass SVT tech to discuss my oil leak. I pasted my previous post on my first visit below.
I need to know if their are any '01 Cobras that have an extrusion out the front of the oil pan. It is a hard plastic type material that sticks out about 3/8" on the direct front of the oil pan and appears to be bent back around the flange of the oil pan. I am trying to get a digital camera and post a pic for comaprison. It would be great if I could go into the meeting armed with some of the same type gasket problems. Any help would be greatly appreciated. The SVT tech says that I bent the oil pan when I put pulleys on the engine. In addition to being a dumb-smart-ass he is blind to begin with because if he had looked at it closely enough he would have seen the gasket is extruded out and bent around the flange of the oil pan. I told a friend at work what happened at the dealership and he said I bet the tech looked at it and saw the pulleys and probably thinks you took the crank pulley off with a crow bar. Like I said he is a dumb-smart-ass. You could not get the crank pulley off with a crow bar. In addition, I passed this guy through the door as I went into the service area to find out what they found and I spoke and said "Good morning" to him and that SOB gave me a dirty look and walked right past me without so much as a nod. A few minutes later I found out he was the tech that looked at my Cobra. When I go over there Monday, I going to set things right with this C. Sucker.
My earlier post: "01 Cobra Oil Leak"
I took my Cobra to my SVT dealer for two leaks. A fitting on the power steering is leaking and I have a substantial oil pan leak.
I noticed a dirt film collecting around the crank pulley shortly after I bought my Cobra. I got up under the car and noticed a bad looking rolled over extrusion coming out of the front of the oil pan. It is pretty hard. It wasn't really leaking where you could see oil pouring. Just a film. It has gotten worse and worse. When I dynoed this past Saturday, I actually created a puddle 3 inches in diameter sitting on the dyno.
I call my SVT dealer and set up an appointment for Tuesday morning. I ask about the free loaner car for '01 SVT buyers and they tell me only for extended repairs. I tell the that is not what the policy says and they give no response. I ask what they consider a extended repair and they say 24 hours. They take the car in the back and shortly thereafter pull it back out front. I go into the service department and they tell me the power steering leak is under warranty. I ask what about the oil leak. They say you put U/D pulleys on the car and bent the oil pan. I say no I didn't and that it is the gasket that is sticking out. They told me the service manager was out until Monday and that he would make the call. I drove off pissed as hell.
When I got home I decided to call the GM of the SVT dealership. He is nice and says he will check with his service people. HE calls me back and reaffirms what his service people stated to me. I told him that his service man is stupid if he thinks that oil pan is bent. The flange is not even flush with the front of the motor. I told him you would have to stretch it out and pull it down. He then tells me how trained his tech is and theat he is almost a master mechanic. He then tells me that even if the leak is a under warranty, the mods that I have done will cause additional work and cost extra money out of my pocket. I told him that L/T headers would not cause his tech any additional work. He told me that I could either take it to another dealer or wait until Monday. I hung up and called SVT.
They said they could not help with warranty problems. I asked them about the loaner and he said you should get a car no matter the length of repair time. I also asked him if I could take the car to any Ford dealer even if they weren't an SVT dealer and he said yes. The back of the SVT supplemental handbook clearly states that any warranty can be performed at any Ford dealer.
I call another Ford dealer and ask them if I can bring in my car and they tell me they can not do warranty work on a SVT vehicle. I tell them that that's funny because I just got off the phone with SVT and they say that I can and that the handbook also says that it can be warrantied at any dealer. She says really. I say really. I then thank her and tell her that I will file a complaint.
I am going to get this fixed under warranty with no expense out of my pocket. I am about to call the GM again at my SVT dealer and take the car back down and get under it with hime and his dumbass tech and ask him how he can confuse a gasket with an oil pan flange.
Federal law states that the dealer has to prove that a mod caused the problem. Damn I'm glad they fired Nasser from Ford. Maybe now we will see what Ford used to be all about. I know that when they tightened down the oil pan, the gasket extruded and that to get the crank pulley on without it rubbing the gasket, the used a mallet and bent it back.
I need to know if their are any '01 Cobras that have an extrusion out the front of the oil pan. It is a hard plastic type material that sticks out about 3/8" on the direct front of the oil pan and appears to be bent back around the flange of the oil pan. I am trying to get a digital camera and post a pic for comaprison. It would be great if I could go into the meeting armed with some of the same type gasket problems. Any help would be greatly appreciated. The SVT tech says that I bent the oil pan when I put pulleys on the engine. In addition to being a dumb-smart-ass he is blind to begin with because if he had looked at it closely enough he would have seen the gasket is extruded out and bent around the flange of the oil pan. I told a friend at work what happened at the dealership and he said I bet the tech looked at it and saw the pulleys and probably thinks you took the crank pulley off with a crow bar. Like I said he is a dumb-smart-ass. You could not get the crank pulley off with a crow bar. In addition, I passed this guy through the door as I went into the service area to find out what they found and I spoke and said "Good morning" to him and that SOB gave me a dirty look and walked right past me without so much as a nod. A few minutes later I found out he was the tech that looked at my Cobra. When I go over there Monday, I going to set things right with this C. Sucker.
My earlier post: "01 Cobra Oil Leak"
I took my Cobra to my SVT dealer for two leaks. A fitting on the power steering is leaking and I have a substantial oil pan leak.
I noticed a dirt film collecting around the crank pulley shortly after I bought my Cobra. I got up under the car and noticed a bad looking rolled over extrusion coming out of the front of the oil pan. It is pretty hard. It wasn't really leaking where you could see oil pouring. Just a film. It has gotten worse and worse. When I dynoed this past Saturday, I actually created a puddle 3 inches in diameter sitting on the dyno.
I call my SVT dealer and set up an appointment for Tuesday morning. I ask about the free loaner car for '01 SVT buyers and they tell me only for extended repairs. I tell the that is not what the policy says and they give no response. I ask what they consider a extended repair and they say 24 hours. They take the car in the back and shortly thereafter pull it back out front. I go into the service department and they tell me the power steering leak is under warranty. I ask what about the oil leak. They say you put U/D pulleys on the car and bent the oil pan. I say no I didn't and that it is the gasket that is sticking out. They told me the service manager was out until Monday and that he would make the call. I drove off pissed as hell.
When I got home I decided to call the GM of the SVT dealership. He is nice and says he will check with his service people. HE calls me back and reaffirms what his service people stated to me. I told him that his service man is stupid if he thinks that oil pan is bent. The flange is not even flush with the front of the motor. I told him you would have to stretch it out and pull it down. He then tells me how trained his tech is and theat he is almost a master mechanic. He then tells me that even if the leak is a under warranty, the mods that I have done will cause additional work and cost extra money out of my pocket. I told him that L/T headers would not cause his tech any additional work. He told me that I could either take it to another dealer or wait until Monday. I hung up and called SVT.
They said they could not help with warranty problems. I asked them about the loaner and he said you should get a car no matter the length of repair time. I also asked him if I could take the car to any Ford dealer even if they weren't an SVT dealer and he said yes. The back of the SVT supplemental handbook clearly states that any warranty can be performed at any Ford dealer.
I call another Ford dealer and ask them if I can bring in my car and they tell me they can not do warranty work on a SVT vehicle. I tell them that that's funny because I just got off the phone with SVT and they say that I can and that the handbook also says that it can be warrantied at any dealer. She says really. I say really. I then thank her and tell her that I will file a complaint.
I am going to get this fixed under warranty with no expense out of my pocket. I am about to call the GM again at my SVT dealer and take the car back down and get under it with hime and his dumbass tech and ask him how he can confuse a gasket with an oil pan flange.
Federal law states that the dealer has to prove that a mod caused the problem. Damn I'm glad they fired Nasser from Ford. Maybe now we will see what Ford used to be all about. I know that when they tightened down the oil pan, the gasket extruded and that to get the crank pulley on without it rubbing the gasket, the used a mallet and bent it back.
