So, I'll get started. Mine is a vintage 1981 Suzuki PE400 2 stroke. As you can see it's just about completed and ready to ride this summer. And yes, I know that these are RM graphics on a PE. I like they way they look better than the PE graphics. :beer:
Some before, during, and after photos...
1996 Boston Whaler Rage 18 Jet boat with a slightly warmed over 351 Red Line (Ford) engine. It makes about 300hp and will run about 50 mph with just me in it and a light load of fuel.
2003 Mustang Mach 1 with a little under 12,000 miles. Yes… 12,000 miles. I am the original owner and ordered the car new. Although located in Ohio the car was purchased in GA. I have never driven the car in the snow and only a handful of times in the rain. You won’t find a nicer Mach 1 than this...
My new project is home.
Since I’ve taken the Mach 1 about as far as I care to and there is nothing like cruising around in a vintage car I thought I would try my hand at a Mopar. I have restored several old Fords in the past and think it’s time for a change of pace. This will be my first Mopar...
Steeda Sport Springs for 99-01 Cobra.
Made by Hyper-coil. Say Hyper coil right on them
Perfect condition.
New they are $289.95 + shipping.
I am selling for $175.00 shipped to the lower 48.
Photos below are of springs and my Mach 1 with these springs installed. (The Mach has a 03 IRS in...
MRT stainless catted H-pipe for 99-04 all Mustangs, Mach 1, & Cobra with approx 6000 miles.
The good:
Other than a few scratches on the bottom of the cat heatshields this pipe is in very good condition.
The bad:
I used to run CC inserts to quiet the car down for my wife when we would go out...
My son’s 2003 Lightening is missing when cold and the computer says it is the #3 cylinder. So far we have changed the plug, swapped the COP, swapped the injector, cleaned the EGR valve, and changed IAC.
The truck only misses when cold and will stop missing within the first minute or so after...
Taken at the shop my son works at. (Allspeed in Peach Tree City GA) In the vids is my son giving the MM suspension a test at the shop skid pad and on the dyno the car made 447hp to the rear wheels. It was still making power at 6,500 rpm but we decided to hold the rpm to this level since we...
Kind of cool being towed by a Lightening.
Going in for full MM front suspension and rear coil overs along with headers. It should be nice and will complete the car.
So here is what you get with the factory Vortech chip that comes in the Mach 1 kit with air to water cooler. The A/F was measured before the cats so is accurate.
The dyno operator said he didn't have much experience with returnless systems and wasn't comfortable tuning the car so I'm going to...
Hi all,
I know a custom tune is always better then what comes in the box but can some of you guys share how much power you picked up with a custom tune over the supplied Vortech chip and if there were any issues with the Vortech tune that may have caused engine damage?
Also, I'll be getting...
For sale is a used set of Steeda underdrive pulleys for a Mach 1 or non-supercharged Cobra. These are the best pullys made for the 4.6L DOHC engine. The pulleys are in excellent shape but do show normal wear as they have approxamately 10,000 miles on them.
Please Note: the Mach 1 pulley sets...
Check out my son's car in Modified Mustangs magazine. There are some small errors in the article but all in all it's not bad. Keep in mind he is only 19.
http://img220.imageshack.us/my.php?image=save00085nt.jpg
http://img104.imageshack.us/my.php?image=save00090ki.jpg...
It appears the 03 IRS is no match a Mach 1 either as I exploded the rear cover last night.
I down shifted from 4th to 2nd at about 40 mph hitting the gas hard to pass a car and boom! The only thing I can figure is that the cover must have been stressed by the owner of the Cobra it came out...
I'm not getting much action in the regional forums so I'm posting this here. If anyone would like to come please contact me.
We have enough cars for the discount but still have some slots open.
Follow this link.
http://www.svtperformance.com/forums/showthread.php?p=2689810#post2689810...
I'm not getting much action in the regional forums so I'm posting this here. If anyone would like to come please contact me.
We have enough cars for the discount but still have some slots open.
Follow this link.
http://www.svtperformance.com/forums/showthread.php?p=2689810#post2689810...
I have reserved a day at Dyno Lab in Marrietta GA on Sept 24 at 9am.
I have slots for a few cars left. If anyone is interested let me know before Tuesday. First come first serve.
A/F will be extra.
Go here www.dynolab.net for info.
1998 16 foot open car trailer for sale.
Pretty typical. Has brakes on one axle, dovetail, slide out ramps, almost new tires on one axle, fair tires on the other. Extra heavy diamond plate runners with wood center, 3500# axles, small toolbox. Pulls nice & straight. Never wrecked.
$1000...
Mrt H pipe & Magnaflow vids
If this works you'll see vids of my 03 Mach 1 with a MRT catted H pipe and Magnaflow cat back. The car has a 03 IRS in it so it does have the Cobra cat back with its specific mufflers.
ftp://ftp.pfabrication.com/FOR_THREADS_WONT_BE_MOVED/mach 1 drive by.WMV...