Search results

That can be adjusted with the nGauge.

I'm selling a 2015-2016 Mustang GT350R Steering Wheel Kit. It was installed and used for about 6 months. Comes with everything that came in the box from Ford Racing. Still New condition. $290 shipped.

I bought these from corral members and I ended up not using them. They are still in the shipping box they came in. PAS Xtreme Mass Air Sensor with 4" Housing - $190 60lb/h Siemens Deka Injectors EV1 - $250 OBO

I am selling my Flowmaster Scavenger X pipe. I had it installed on the car for about a month and a half. It sounds good especially with the Flowmaster Outlaws. I decided to go with a custom H pipe. When I had the Flowmaster X pipe installed, about a half of an inch or less was cut off the back...

I am selling my Modified factory intake with K&N air filter and Airaid's modular elbow. $190 shipped.

I am going to get CompCams new CR series camshafts after I complete my exhaust. On their SEMA video they are claiming 50-60hp from these cams. I am looking for a shop to install them and dyno-tune it at the same location. I did some searching and I haven't seen much info on them. I guess I'll be...

I have a Brand New in the box Aeromotive 340 fuel pump for sale. Part # 11140. Aeromotive 11140 Aeromotive 340 Stealth In-Tank Fuel Pumps $150 shipped [/URL][/IMG] [/URL][/IMG]

I am selling my R 302 block. I was planning on putting together a 363ci setup for boost. I have collected all the parts for the shortblock, but since it's not together yet I've decided to sell it. The rotating assembly is for sale in my other ad. Specs on the block Bore: 4.105" stroker...

Change of plans sale!! Along with my R 302 block I have for sale in another ad, I am selling the rotating assembly which consist of: eagle crank, eagle rods, probe srs pistons, perfect circle fire power ring set, clevite main and rod bearings. The crank and rods are used (was used in the...

I searched and didn't find this anywhere so I'm posting this up if everyone haven't seen this. I think this is a great deal for a fully forged low compression coyote! Ford Racing Performance Parts -------- Ford Racing's 5.0L Mustang "Aluminator" crate engine is a modern 5.0L 32-valve DOHC...

repost delete please

I have a 351w victor jr intake: $170 shipped (US)

I'm looking for a good shop where I can get my heads completely worked over. Within the South GA or North FL area. I'm looking for a local shop but if I have to ship them I will.

I am selling my Mallory Ignition System. I'm going a different route with the car. I will also be parting my 398w stroker. Mallory Hyfire Ignition 6853M - Mallory Ignition 6853M - Mallory HyFire VI-AL Digital CD Ignitions - Overview - SummitRacing.com Mallory Promaster Coil 29625 - Mallory...

I have 2 Magnaflow bullet mufflers (same as the JDM silverbullets). They was welded in place of the stock mufflers. I'm going with a completely different midpipe and catback. asking $100 + shipping I will have the exhaust removed this afternoon.

I have a set of used Scorpion 1.72 roller rockers with poly locks and 7/16 studs for sale. asking $165 + shipping

I have a Glow Shift wideband air/fuel gauge for sale. comes with everything for install and works great. asking $100 shipped Black 7 Series Digital Wideband Air Fuel Gauge

wrong section. please remove

pillar gauge pod for 2 gauges $27 shipped AiRaid CAI with used filter $55 shipped

I have a autometer boost gauge for sale. asking 32.00 shipped. boost gauge for sale only

I have a autometer boost/vac gauge for sale. asking $32.00 shipped.

this coil was only used on two start ups for a total of 10 minutes then was switched out for a Mallory coil to match everything else. Its still basically new. asking $30.00 shipped, obo.

I have a mustang gt driveshaft for sale. the length is 45.5 inches from u-joint center to u-joint center. it's in good working condition. asking $65.00 shipped, obo.

I seen three Lightnings there on Saturday. two of them was red and the other was white. It looked like one of the red lightnings broke something at the 1/8. was that anyone here? I also have some vids, but my camera pooped out on me halfway through the event. It was recording but not saving...

I am putting my heads in the shop to have them milled while I convert my fuel system to E85. Sense I will be running E85 that can handle higher compression, will I gain anything or is it worth the money spent by milling the heads to 13:1 or 13.5:1 cr? I will also be using 100 shot(not so often)...