Recent content by suprsnke

For sale: Maximum motorsports HD rear control arms and PHB. Parts are in good condition and are virtually rust free. The part number for the LCA's are MMRLCA1 and the PHB is just PHB. The RLCA fit 94-98 and the PHB is for 79-98. Looking to get $150 for the RLCA' so and $250 for the PHB. All...

I have a set of heads from my 98 cobra. They have 50k miles on them. I need them gone. Make me an offer. I used the original intake cams. They currently have mach1 intake cams in them. Email me for fastest response. I need money to race! Ray [email protected]

I have 2 IMRC controllers that I took off of my 98 Cobra. 1 of them is only 5 years old and has less than 15k miles on it. Make an offer. Email me for fastest response. Ray [email protected]

Looking to buy an SCT tuner for a 98 cobra. Id be using it to give to my tuner to write a tune for my car. Email me for fastest response. Ray [email protected]

My 98 cobra is a dedicated road race car. Just finished installing and dynoing a new 4.6 dohc motor with a coil on plug conversion. While at the dyno today i was informed that my factory tach is incorrect. It reads high by about 400 rpm at idle. While the engine is revving at 7000 rpm the tach...

98 cobra dedicated road race car. Just had a new engine dynoed and was kind of disappointed. Stock displacement 4.6, with forged flat top pistons good for 11:1 comp. Stock C heads with 98 intake cams. Stock intake and throttle body. Long tube headers and a non catted x pipe. The car dynoed...

Looking to buy an oil cooler from a 96-04 cobra or mach 1. Have cash. Need ASAP. Email me for fastest response. Thanks Ray [email protected]

I'm building an 03 Mach motor for a road race car. I installed the intake cams from my 98 motor into the 03 heads. The 98 cams use a 12mm bolt for the sprocket and get torqued to 80-95 ft-lbs. The 03 heads have a 10mm bolt. I snapped the bolt when I torqued it to 90 ft-lbs. What is the...

Im currently putting my motor back together. It's an 03 Mach 1 block with a 98 cobra pump. I'm installing MMR billet gears in the stock pump housing. Is there any literature any where on how the pump goes back together? I really just need the torque specs on the screws and if there is supposed...

For sale: 96-98 cobra intake spacer. This is an MMR piece. Had it on my car for 2 weeks. Deciding to go to c heads and intake. No longer need this spacer. Will sell with hardware and gasket as sold from MMR. $75 shipped. Email me for fastest response. Ray [email protected]

For sale: ford racing 3.73 gears. These were used in literally 4 road races. They have less than 200 miles on them. $125 shipped. Email me for fastest response. Ray [email protected]

For sale. Melling high volume oil pump. Pump has steel gears. Part number is 10227. Used for 1 year. Works just fine. Email me for quickest response and for pics. I paid $325 for it. Selling for $225 shipped. obo. Ray [email protected]

For sale, complete 99 cobra IRS. Its located in northern NJ. Has only 35k miles on it. Complete with rotors, calipers and springs. I have all the bolts and brackets to bolt it in. I will not ship. I can deliver any where in the tri state area. $200. Again, I will not ship. Email me for...

Does anyone know where to go for sn 95 fender flares? Looking to put 1"wheel spacers on and need flares to cover the tires Ray [email protected]

Wtb: forged flat top pistons. They need to be standard bore and stroke. Have cash in hand ready to go. Email me for fastest response. Ray [email protected]