Recent content by gtmuscle

looking to buy an 99 or 01 coupe in florida. slightly modified is ok but must be NA

I know this subject has been gone over before but my specific questions are: on a 2007 GT500 with H&R race springs and a BMR adjustable panhard bar will a 10.5 inch 20 wheel with a 45 offset fit in the rear fender without any modification? I want t put a 315/30/20 toyo R888 on but I need...

I am looking to get new wheels for my 2007 GT500 in torch red. I want to stick with 18's as i just bought tires 1,500 miles ago. I am leaning towards chrome or silver, but very limited in 18's. thinking of forgestar F14's in silver but have not seen any pics. post up any pics with...

I want to get a set of 18" wheels and do not want steeda ultralites. TSW says they don't have any that fit. any suggestions with pics!!

Does anybody have any pictures of the CS56 wheels on a GT500.

Have a red 07 GT500 and want to know what is the best wax for a flat paint. I do not want to do the porter cable route and want no white residue to dust off. car was clayed a few months ago and used mazerna wax, just dont want another 8 hour waxing session!

I put an MRT O/R H pipe on my 2007 GT500 with the Bassani Race axle back. The sound is raspy and very loud, i want to change the axle back but what one will make it sound deeper and not as raspy. I have always had magnaflow on previous mustangs wnd liked the sound, but heard the fit was...

I have a buyer for my 03 anniversary cobra. I am thinking about getting an 07 GT500 with about the same miles (17,000) and with just a little more power, 550 for the GT500 and 525 for the cobra. If anybody has done this, are there regrets or was it a good change?

re-port or 2.8 kenne bell I had my eaton ported with a Stiegemeier stage 5 port about 9 months ago. I have put approx. 2,200 miles on it since and last week it started making this whistling sound. My tuner took it off and found that the welds in the plate broke and the plate was loose...

S&R Performance in Tampa holds an annual poker run. this year it is on 2/27/11 @0830 and is about 180 miles of twisty turny back roads in pasco and hernando counties. There usually is alot of european and ricers with a few domestics, inclouding about 10 stangs. we are trying to bump up...

i am looking to trade my 2003 silver anniversary edition with 16,700 miles for a 2008 to 2010 GT500 plus cash. I have the title and it is in perfect shape with no dings dents or scratches. The following is a list of mods: Steggy stage 5 ported blower Ported dragon plenum 6lb metco...

I ordered some brembro rotors and did not like the drilled look. So, not I am contemplating Baer or DBA with hawk HP+ pads. I am thinking about the two piece Baer or the one piece DBA 4000 series. The 2 piece DBA seem expensive and overkill for street and occassional autocross. Any...

Have stock headers and o/r prochamber. what is best o/r x pipe for stingers. also, how well do the stingers polish???

I see that Stainless steel systems and Stailess steel works both make polished catbacks. Any body have them for the terminator? i am looking for new, want polished to save time from polishing others i thought i would get one of these systems. or i could buy the bassani as it seems to be the...

i have stock headers, O/R prochamber and currently magnaflow catback. It sounds good when wide open but i rarely drive it and want to get a little louder. i also want to polish the new one and do not like the weld on the SLP so thought of stingers or bassani. i also think the magnapacks pop to...