Hello everyone! I am almost finished up with my build on my 03 DSG cobra with the HPP Twin Turbo kit. The kit has the upgraded 61mm turbo's. I am also running a fully built 4R70W trans, and tons more that I can go into detail about later on.. But I am having some issues with fitting the exhaust...
I have a set of manley forged H beam rods with arp 2000 rod bolts. the rods have been resized for the arp 2000 bolts. less then 1500 miles on them since the new arp bolts have been installed. I will be able to get pictures of them this evening after work. $450 shipped
I am parting out my 97 cobra turbo car. I will be selling the car as a roller with a Wolfe 6 point roll bar, fuel system full interior and all suspension etc. pending
04 Mach lower/01 cobra upper intake $350
BBk twin 65mm TB $240
Kellogg 5.0 stroker crank and eagle 5.85 stroker rods w/ 2.1 rod...
I have a sct X cal3/3000, I bought it for my car so I'd have one for tuning. My tuner ended up flashing my computer instead. So I don't need it, it's unlocked and ready to go. $260 shipped.
I also have a sct SF tuner that came with my car, it has been unlocked from my car, but it has 3 custom...
I am looking for a plastic radiator cover/core support cover. It goes from the header panel to core support (plastic piece around the area of the hood latch etc). Idk if 94-95 is the same? But I need one for my 97 cobra. Lmk what u have, and must be in good shape!
Also looking for 100%...
I have a Ported Short Runner (Al Pappito) 99/01 cobra intake setup for sell. This is for the Upper/Lower. The upper has been modified for SBTB.. You get the following, the complete upper/lower with accufab SBTB, Idle air control valve setup. $700plus fees/shipping.
This intake is built for...
I have a magnaflow catback for SRA. I am wanting to trade the flow tubes and mufflers for a set of magnapacks w/ flowtubes. Or I will trade complete catbacks.. Lmk what u have.
ok, well this is the final push.. I am wanting to trade my Fully Built Dynamic M2 C4 setup for modular engine. It has the alum bell, 3500 9.5" stall, Full Manual reverse valve body W/Trans brake.. alum driveshaft. Large trans cooler w/fan, A/N lines and fittings.. B&M hammer shifter.. everything...
ok, i have a few parts that i have no need for. i dont have pics at the moment, but can text them if needed. add fee's
I have a NX wet/dry kit. I have both nozzles and solenoids for the kit, i also have a nos bottle heater for the kit, NX purge kit as well. the kit has tons of jets...
Like the title states, I am wanting to trade my built C4 trans setup. (Setup for modular engines) This is a long shot, but I'm looking for either a nicely built 4r70 or a solid T56 setup(with 26 spline etc).. I just had the trans gone thru, and new clutches installed. Everything works as it...
ok. I have some parts that i no longer need, or will not use anytime soon.. here it goes..
NX nitrous kit.. i have tons of extras for this kit!! many switches, fittings, lines, tons of jets, wet and dry nozzles, heater, purge, etc.
comes with a Brand New dynotune nitrous controller/window...
Like the title states, I am wanting to trade my built SRA for an IRS with ftbr kit and diff brace or cover.. Want to trade exhaust and all, shoot me a pm if u wanna work a deal.. Located outside the Tulsa, OK area. Will travel within a few hours.
My SRA is a 01 housing, w/ 3.55 gears and 03...
ok well im looking to work a deal for a "built" SN95 cobra + cash, doesnt matter if its 94/95 built push rod car, or the 96-98 4v mod motor.. so if you have a built/ big blower,or turbo car and want to work something out lmk... its a long shot, but im going to try.. I may take a built, or...
ok well im looking to work a deal for a "built" cobra, prefer 04, but 03 is fine if its low miles!! I am looking for something with a bigger blower or turbo. 6spd or auto.. i will add cash depending on the right car as to how much!! so if you have a built/ big blower,or turbo car and want to...