Recent content by eebj01

I have a Cervini 2 1/2" Cobra R cowl hood for 99-04 Mustang. It is brand new in the box. I bought it in November. I am up the turnpike from you in Nazareth PA (just north of Allentown/Bethlehem). You can email me at [email protected] Thanks, Ed

Pro Racer package, ECU, X cal 2, LaSota training disk have been sold

MSD 2 step is sold.

That is NOT correct. The Pro Racer Package is linked by SCT to the ECU. It is not like an X2 or X3 where you can return the vehicle to stock and then use it on another vehicle. The Pro Racer Package uses a dongle that plugs into your laptop and that dongle is linked to the ECU on file at SCT...

I would be willing to sell the following separate: Cluster $160 MSD 2 step $170 SCT 2400 $60 Stock engine harness $125 Modified engine harness for KB mammoth $125 SCT chip $50 Dynojet wideband $120 AEM injector driver $140 ECU harness $100 I'd like to keep the ECU, Pro Racer package, X2, and...

I am going to Holley EFI with digital dash so I am selling all of the electronics out of my 2003 Cobra. Here is a list of the stuff that I have available: HSFO computer ECU harness with lengthened mass air and IAT sensor wires stock engine harness engine harness for Kenne Bell mammoth (drivers...

Cams have been sold. Thanks SVT Performance!

I have a set of 4 Comp Cams XE274BH-116 (p/n 106460) for 4.6/5.4 DOHC. These are their XE-R Supercharged or Nitrous grind cams. Specs are: 273/275, 238/240 @ .050, .475/.450 lift, 116 lobe sep. Cams were used with a Kenne Bell 2.8 Mammoth and produced 800+ rwhp. Cams are ready to install in...

For sale is a complete Eaton swap setup minus the supercharger, injectors, and rails. This has everything. Balancer, lower pulley w/ cage, all bracketry, remanufactured alternator, lower intake, intercooler, all intercooler fittings and hoses, Bosch intercooler pump and all metal lines and...

For sale: American Racing Headers stainless 1 7/8 primaries with 3” merge collectors for 99-04 DOHC 4V. Also includes 3” stainless X pipe with high flow catalytic converters. Two extra O2 bungs have been added for widebands. Also includes upgraded clamps. These headers fit like a glove even...

Kenne Bell 2.8 Mammoth for 2003-2004 Cobra. Comes with Billetflow quick change pulley setup and auxiliary idler for increased belt tension. Billetflow 3.400 pulley and 2.930 pullies are included. Includes the Mammoth inlet, Mammoth throttle body, inlet piping with integral mass air housing...

I'm putting together an 8.8 solid axle for my Cobra. I'm trying to decide what gear ratio to go with. I'm torn between 3.55 and 3.73 primarily. For anyone that has a large twin screw such as a Whipple 3.4 or Kenne Bell Mammoth 2.8 and has a race setup (high boost/race fuel, automatic trans...

I’m having some issues getting my combination to drive correctly. This is the combo: 2003 Cobra HPP Stage 3 cams with high overlap Kenne Bell 2.8 w/ Mammoth inlet and huge monoblade throttle body 80 lb injectors Return style fuel system 300” stroker SCT Pro Racer Package I got this...

I have a complete T-56 setup out of a 2003 Cobra that I’m looking to trade for a complete automatic w/ transbrake. The T-56 was rebuilt January 2013 by Hanlon Motorsports. It has a 26 spline input shaft, all new scynchros, blocker rings, bearings, and gearset. Clutch is a Ram twin disk...

sold