Recent content by Batwood

I'm looking for some possible ideas on my problem child of a car. Sorry for the long post... 2004 Cobra DSS built motor, Roush heads, Comp Cams etc... 3.4 Whipple @26psi 4R70W Auto The car was tuned a few months ago and made 660whp with belt slip on 19psi. Unlocked converter. I put a...

In 2014 I built a 4R70W trans with a Performance Automatic kit and a PTC single disc converter with billet cover. They say its good for 950hp with the right sun gear. The car went 9.99@141 with 2.3 whipple, stock motor and built 8.8 solid rear. After some issues last year, I ended up with...

04 Cobra. 3.4 Whipple. 3.2 Upper, Stock Lower. E85, Headers, 4r70W, 8.8 with 3.55s. Anyways... I dyno'd yesterday and this set up made 29psi. Which was much higher than I expected, based on some internet research. We left the car at 13* timing so it wouldn't explode until I get head studs...

I'm looking for a passenger side roof molding for my 04 Cobra. Would prefer silver. Its the long piece going from below the windshield all the way back to the top of the rear window. Thanks

I'm upgrading my 2.3 Whipple to a 3.4 setup... it will be coming off in a few weeks. I've had it for about 2 years. Less than 10k miles on it for sure. I'd guess around 5k miles total. When I got it, there was still writing in marker on the rotors. Gen II, polished. Also have an accufab...

PB Last year with the T56/IRS was a 10.7@134 on a 1.7 60'. 641whp. Over the winter, I did a 4R70W swap and threw in a solid rear axle and 3.73s. Also a UPR K member and coil overs up front. The car was not retuned, the exact same tires were used, and the only engine change was going from...

I've got an 04 Cobra that I did a 4r70w swap on this winter. I got screwed by a member on here with my "built" trans that turned out to be junk... Anyways, after a complete new rebuild, new case, new drums, pump, converter, and a rebuilt valve body, I have a fluid leak. I watched it run...

I'm looking for a torque converter for my 4r70w. Multi-disc with lock - up... let me know what you guys have. Would prefer PI or PTC. Thanks

I'm looking for a torque converter for my 4r70w. Multi-disc with lock - up... let me know what you guys have. Would prefer PI or PTC. Thanks

Looking for a built SRA to swap into my Cobra. Ideally, it would include control arms, exhaust, springs, shocks, driveshaft... But let me know what you have. I have a couple stock IRS shafts, I could get a pinion flange and swap it, if needed. No abs is needed and I have my own brakes. I'd...

Looking for a built SRA to swap into my Cobra. Ideally, it would include control arms, exhaust, springs, shocks, driveshaft... But let me know what you have. I have a couple stock IRS shafts, I could get a pinion flange and swap it, if needed. No abs is needed and I have my own brakes. I'd...

A couple weeks ago, I ran at Cordova, Illinois. Best pass was a 10.97@128 on a 1.67 60. (7.1@102 in 1/8) Best 1/8 was a 6.9@109... same 60' but blew a vacuum line and shut down going into 4th. Anyways, I was at CFR, Iowa yesterday. My N2MB launch control started acting really strange, so I...

Headed up to Cordova Sunday for a local forum Grudge Day. My best last year on the ported Eaton was an 11.4@123 on a 1.8 60'. First pass right off the highway was 10.9@128 on a 1.6 60'. I let the car cool down for the next pass and the person in the tower screwed the clocks up so my...

If everything works out, I'll be picking up a built trans this weekend with an RST clutch and some other goodies. I'm leaving my Spec 3+ in the car, so I'll be selling the clutch. I'm told it has 500 miles on it and is the 26 spline. If all works out, is anybody looking for a deal on a good...

I just recently got my build finished and was driving around today. I did a 3rd gear pull from probably 50mph. As soon as I floored it, the car started shaking and made a horrible grinding noise. I pulled over and discovered I had lost all gears. It ran fine, but everything else was silent...