yes they are cheap, but will they work? Drag wheels

[brandonflood123]

http://www.latemodelrestoration.com...ustang-SVE-Drag-Wheel-15X10-Gloss-Black-05-14

they are cheap but i just wanted to know what you guys opinions on them would be, they would be going on a 10 gt500

here are the specs VVVV

Diameter 15" Width 10" Lugs 5 Offset +41 mm. Backspacing 7.12 in. Bolt Circle 4.5 in.

 

[1320 Junkie]

Who cares how much they cost......as long as they work. Specs seem good (7.5" bs is more desireable)and I actually like the look of them.

 

[Cobrav]

 

[Quade]

I run Bogarts with drags and the LMR with Pro's. The LMR/Pro's setup weighs at least twice as much as th Bogart/Drag setup but they work exceptionally well.

 

[BilletProShop]

http://www.latemodelrestoration.com...ustang-SVE-Drag-Wheel-15X10-Gloss-Black-05-14

they are cheap but i just wanted to know what you guys opinions on them would be, they would be going on a 10 gt500

here are the specs VVVV

Diameter 15" Width 10" Lugs 5 Offset +41 mm. Backspacing 7.12 in. Bolt Circle 4.5 in.

they work just fine and for the price ...you can't go wrong

 

[1NA RUN]

I run them on my coyote and love the way they look and perform. No complaints here.

 

[slowbra1]

They look like Dark Stars, I wonder if they are made by the same manufacturer, RUN'EM

 

[ALLKHEINZ]

ran both the 15" gloss black on my 9.47 run on the Shelby and used the same set on my 13 5.0 to go 9.16 at almost 152mph....no stupid washers to use either. I ran those numbers with stock acorn lugs..

 

[slowbra1]

ran both the 15" gloss black on my 9.47 run on the Shelby and used the same set on my 13 5.0 to go 9.16 at almost 152mph....no stupid washers to use either. I ran those numbers with stock acorn lugs..

Damn on the stock acorns

 

[brandonflood123]

Who cares how much they cost......as long as they work. Specs seem good (7.5" bs is more desireable)and I actually like the look of them.

I run Bogarts with drags and the LMR with Pro's. The LMR/Pro's setup weighs at least twice as much as th Bogart/Drag setup but they work exceptionally well.

they work just fine and for the price ...you can't go wrong

I run them on my coyote and love the way they look and perform. No complaints here.

They look like Dark Stars, I wonder if they are made by the same manufacturer, RUN'EM

ran both the 15" gloss black on my 9.47 run on the Shelby and used the same set on my 13 5.0 to go 9.16 at almost 152mph....no stupid washers to use either. I ran those numbers with stock acorn lugs..

ALLKHEINZ did you have to relocate any of your suspension components?


thanks for all the feed back guys! i think im going to get these. what tires would you recommend?

 

[slowbra1]

Rear Mickey Thompson ET Drag Slicks 3055S 28-10.5 and Front Phoenix 27x4.5 17

ALLKHEINZ did you have to relocate any of your suspension components?


thanks for all the feed back guys! i think im going to get these. what tires would you recommend?

Rear Mickey Thompson 28x10.5 ET Drag Slicks Part# 3055S and Front runners Phoenix 27x4.5 17 http://www.dragracetires.com/4-0-22-5-15-phoenix-drag-front-191.html

http://www.uprproducts.com/mickey-thompson-tires-28-105-15-stiffwall-et-drag.html

 

[GT Premi]

Yeah, OP, don't worry about guys dropping $tacks on wheels. Buy what works for your intended purposes and fits in your wheel budget. Just read up on the construction specs of the wheels to make sure they can handle what you're going to put them through. I have a set of cheap wheels on mine [not drag wheels] that all four wheels cost less than just one of the forged wheels a lot of the guys on this forum have on their cars. They might not be as strong or as pretty, but they weigh A LOT less than those forged wheels, and weight reduction is the most important thing to me.

 

[Black Sex]

Here are my SVE 15x10 with 275/60r15 tire. Tires are tucked and no rubbing issues. You will have to relocate the rear sway bar though. Each wheel/tire weighs 43lbs

 

[FEARSNO1]

T
Here is my SVE Drag pack! I love them! Even have a few buddies that run them daily! I love the fact that I can just bolt them on with stock lugs. I even weighed them with my buddies RT/S setup that had the same tires and they were less than a pound difference. I've ran in the 9's with them on a number of occasions

 

[brandonflood123]

TView attachment 28770View attachment 28770
Here is my SVE Drag pack! I love them! Even have a few buddies that run them daily! I love the fact that I can just bolt them on with stock lugs. I even weighed them with my buddies RT/S setup that had the same tires and they were less than a pound difference. I've ran in the 9's with them on a number of occasions

Here are my SVE 15x10 with 275/60r15 tire. Tires are tucked and no rubbing issues. You will have to relocate the rear sway bar though. Each wheel/tire weighs 43lbs

Rear Mickey Thompson 28x10.5 ET Drag Slicks Part# 3055S and Front runners Phoenix 27x4.5 17 http://www.dragracetires.com/4-0-22-5-15-phoenix-drag-front-191.html

http://www.uprproducts.com/mickey-thompson-tires-28-105-15-stiffwall-et-drag.html

thanks for these guys and as far as relocating the sway bar does anybody have any good relocation bracket setups they would recomend? and possibly a link on where to buy them im strongly considering this, also does the pan bar need to be relocated?

 

[FEARSNO1]

Plenty of companies have the relocation brackets, they are simple and cheap, ($35~), panhard bar doesn't need to relocated