Yates SC1 heads:I just got the heads back from Mike at Hi-Flow Heads 708-396-0505, feel free to call him about these heads. The heads just got a fresh valve job, the valves, springs, retainers only have 10 passes. This setup will make 900+ horsepower on motor and depending on the nitrous tune-up will easily run 7's at 170+mph in a 3000lb coupe!! All prices are negotiable and I will make a nice package deal/price.
Pics are here... ImageShack Album - 25 imagesIf you would like any other specific pics please let me know and I will get them posted asap. I will have pics of the heads and rockers this weekend I thought I had them on imageshack but I guess not.
Parts below have 10 passes on them.
Yates SC1 Cylinder heads
-Full race porting with excellent low lift numbers
-Titanium intake/exhaust valves and titanium retainers
-PSI valve springs 310-315lbs closed seat pressure good for .900 lift cam
-T&D shaft mount rockers 1.65 and 1.70 (one-piece stand, not individual) with the needle tip bearings, most expensive and heavy duty shaft mount rocker system available.
$5500
Lift Intake Exhaust
.100 --- 83 / 54
.200 --- 155 / 113
.300 --- 241 / 163
.400 --- 310 / 205
.500 --- 338 / 237
.600 --- 359 / 250
.700 --- 379 / 255
.800 --- 388 / 260
.900 --- 387 / 262
Custom made stepped and coated headers,
2.125" into 2.25" into 4" collectors with extensions. These headers were made for fox body with skinny kid motor and mid plates and a powerglide trans. They are all equal length, within 3/4", and have been jet hot coated inside and out.
$800
Wilson Sheetmetal intake for twin dominators
-Port matched to heads
-two foggers installed with purge
-has dominator base velocity plates
-two burst panels
-custom throttle linkage will be included as well as the valve covers (part of the linkage is welded to the driver side valve cover)
-hundreds of stainless jets from .018 to .048
$4500
Custom offset BILLET MSD Distributor (Big $$$)
-Must use this offset distributor with the Wilson sheetmetal intake
$900
All parts below are new in the boxes....
BILLET STEEL CRANK
3.75" stroke crank with 2.75" Cleveland mains
$1500
GRP Aluminum Rods
SB1000X
6.125"
2.225" - 0.941"
0.927" - 1.150"
**$700**
CP Custom Gas ported Nitrous pistons
PISTON SPECS... for a Yates C3 or SC1, may also work with Brodix/Neal heads
4.064"
compression height 1.265"
intake valve relief - (-.13)
pin diameter - 0.927
dish depth - (-0.08)
Pistons made for 3.75" stroke crank and 6.125" rods
PM me your email address if you would like the entire build sheet on the pistons.
**Pistons w/ total seal rings included- $700 **
Pics are here... ImageShack Album - 25 imagesIf you would like any other specific pics please let me know and I will get them posted asap. I will have pics of the heads and rockers this weekend I thought I had them on imageshack but I guess not.
Parts below have 10 passes on them.
Yates SC1 Cylinder heads
-Full race porting with excellent low lift numbers
-Titanium intake/exhaust valves and titanium retainers
-PSI valve springs 310-315lbs closed seat pressure good for .900 lift cam
-T&D shaft mount rockers 1.65 and 1.70 (one-piece stand, not individual) with the needle tip bearings, most expensive and heavy duty shaft mount rocker system available.
$5500
Lift Intake Exhaust
.100 --- 83 / 54
.200 --- 155 / 113
.300 --- 241 / 163
.400 --- 310 / 205
.500 --- 338 / 237
.600 --- 359 / 250
.700 --- 379 / 255
.800 --- 388 / 260
.900 --- 387 / 262
Custom made stepped and coated headers,
2.125" into 2.25" into 4" collectors with extensions. These headers were made for fox body with skinny kid motor and mid plates and a powerglide trans. They are all equal length, within 3/4", and have been jet hot coated inside and out.
$800
Wilson Sheetmetal intake for twin dominators
-Port matched to heads
-two foggers installed with purge
-has dominator base velocity plates
-two burst panels
-custom throttle linkage will be included as well as the valve covers (part of the linkage is welded to the driver side valve cover)
-hundreds of stainless jets from .018 to .048
$4500
Custom offset BILLET MSD Distributor (Big $$$)
-Must use this offset distributor with the Wilson sheetmetal intake
$900
All parts below are new in the boxes....
BILLET STEEL CRANK
3.75" stroke crank with 2.75" Cleveland mains
$1500
GRP Aluminum Rods
SB1000X
6.125"
2.225" - 0.941"
0.927" - 1.150"
**$700**
CP Custom Gas ported Nitrous pistons
PISTON SPECS... for a Yates C3 or SC1, may also work with Brodix/Neal heads
4.064"
compression height 1.265"
intake valve relief - (-.13)
pin diameter - 0.927
dish depth - (-0.08)
Pistons made for 3.75" stroke crank and 6.125" rods
PM me your email address if you would like the entire build sheet on the pistons.
**Pistons w/ total seal rings included- $700 **
