Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
SVT Shelby GT500
Torque for ARP balancer bolt?
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Robert M" data-source="post: 16467980" data-attributes="member: 9628"><p>.......and here is the GT500 Crank Saver Installation instructions......and YES, a torque spec. specific to this install!!!</p><p></p><p></p><p></p><p><strong>Do NOT use the Crank Saver to install crankshaft pulley. Use the installation tools designated by the manufacturer.</strong></p><p><strong></strong></p><p><strong></strong></p><p><strong></strong></p><p><strong>Preparation</strong>: (if using in new crankshaft, proceed to installation section)</p><p></p><p>Remove crankshaft bolt and washer. Removal of the pulley is not required.</p><p></p><p>Clean inside of crankshaft snout to the best of your ability using WD-40, aerosol brake cleaner, and a bristled brush. (e.g. pipe cleaner or toothbrush)</p><p></p><p>Any material left inside the snout may prevent stud from fully seating.</p><p></p><p>Running a thread chaser (M12x1.5) is not required, but highly recommended. An alternative is to remove washer from stock bolt, then fully thread the bolt into crankshaft to clear the lower portion of threads.</p><p></p><p>Clean and remove any residue from the surface of your crankshaft pulley where the washer will rest.</p><p></p><p></p><p></p><p><strong>Installation</strong>:</p><p></p><p> Apply a small amount of ARP Ultra-Torque lube to bottom portion of the Crank Saver stud (short side), and thread stud into the crankshaft by hand.</p><p></p><p>Ensure the stud is fully seated using the 4mm Allen, but do not torque. If fully seated, the top portion of threads will begin just below the face of the crankshaft snout. If you meet resistance before the stud reaches that point, DO NOT try to force. The most common reason for this is residual thread locker and/or dirt in the lower portion of threads, where the current bolts do not reach. Remove the stud and return to preparation section.</p><p></p><p>Liberally apply ARP Ultra-Torque lube onto the flange and threads of the nut and top side (nut side) of the washer. Install washer, then thread nut onto stud by hand.</p><p></p><p>Torque using a 12-point 16mm socket. Recommended torque: 140-150 lb-ft</p><p></p><p>Tip: Place transmission in gear and firmly apply parking brake to prevent engine spinning while torquing.</p></blockquote><p></p>
[QUOTE="Robert M, post: 16467980, member: 9628"] .......and here is the GT500 Crank Saver Installation instructions......and YES, a torque spec. specific to this install!!! [b]Do NOT use the Crank Saver to install crankshaft pulley. Use the installation tools designated by the manufacturer. Preparation[/b]: (if using in new crankshaft, proceed to installation section) Remove crankshaft bolt and washer. Removal of the pulley is not required. Clean inside of crankshaft snout to the best of your ability using WD-40, aerosol brake cleaner, and a bristled brush. (e.g. pipe cleaner or toothbrush) Any material left inside the snout may prevent stud from fully seating. Running a thread chaser (M12x1.5) is not required, but highly recommended. An alternative is to remove washer from stock bolt, then fully thread the bolt into crankshaft to clear the lower portion of threads. Clean and remove any residue from the surface of your crankshaft pulley where the washer will rest. [b]Installation[/b]: Apply a small amount of ARP Ultra-Torque lube to bottom portion of the Crank Saver stud (short side), and thread stud into the crankshaft by hand. Ensure the stud is fully seated using the 4mm Allen, but do not torque. If fully seated, the top portion of threads will begin just below the face of the crankshaft snout. If you meet resistance before the stud reaches that point, DO NOT try to force. The most common reason for this is residual thread locker and/or dirt in the lower portion of threads, where the current bolts do not reach. Remove the stud and return to preparation section. Liberally apply ARP Ultra-Torque lube onto the flange and threads of the nut and top side (nut side) of the washer. Install washer, then thread nut onto stud by hand. Torque using a 12-point 16mm socket. Recommended torque: 140-150 lb-ft Tip: Place transmission in gear and firmly apply parking brake to prevent engine spinning while torquing. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
SVT Shelby GT500
Torque for ARP balancer bolt?
Top