Question About Clearances And Fitment

NoLimitRacing

Member
Established Member
Joined
Sep 11, 2018
Messages
115
Location
So Cal
Just going to drop this here for you…..


I currently make 824 Hp 767 TQ on ID1050x’s. 22 psi of boost, built motor, 2.8KB, pump E85, return system with (2) 465 pumps.

Nice numbers! Geese louise! Can you share a little about the built motor please?

New pistons? Rods? Cams? Heads worked on? Valves?
Just going to drop this here for you…..


I currently make 824 Hp 767 TQ on ID1050x’s. 22 psi of boost, built motor, 2.8KB, pump E85, return system with (2) 465 pumps.

Sorry my ignorance, i only read what you typed and did not see the link you attached first. That answered my questions towards you.

Good shit man!
 

NoLimitRacing

Member
Established Member
Joined
Sep 11, 2018
Messages
115
Location
So Cal
Just going to drop this here for you…..


I currently make 824 Hp 767 TQ on ID1050x’s. 22 psi of boost, built motor, 2.8KB, pump E85, return system with (2) 465 pumps.

I just saw an option for a 132mm or a 150 mm throttle body. Do you remeber which onebtou went with?
 

01yellercobra

AKA slo984now
Established Member
Joined
Oct 5, 2005
Messages
21,125
Location
Cali
Nice! Are you on pump gas or E85?

Could you share your mod list?

Return Style Fuel Sytem?

Dual Pump or Tripple Pumps?

Pump duty cycle % to hit 700?

My goal is to hit 800 + on a dyno.

My car will be stock long block engine (ford racing remanufactured longblock with a stamped build date of 2005), gen v 3.0 whipple, long tube headers 1-7/8", catless H pipe 3", catback exhaust 2.5", BA 2600 MAF, Twin Clutch, Fore Return Style Tripple Pump Fuel System, Strictly E85 , and I think that's it.


Like I said I originally wanted to go with ID1300x but was strayed towards the 1050x by my tuner as well as the vendors websites selling them now that I think of it I believe I also seen the disclaimer on Injector Dynamics downloadable excel file they have for compatibility reference.

What do you think?

I'm running twin 450 pumps, -8 feed and return, Fore rails, and regulator. When I ordered everything I was told I should be good for 850 on E85. And I'm usually on E85.

It's a return system. So FPDC doesn't matter anymore.

The rest is basic Cobra mods. Whipple 2.9 with a standard inlet and Accufab TB. Bassani headers and mid pipe with Stingers. The motor is 100% stock.
 

01yellercobra

AKA slo984now
Established Member
Joined
Oct 5, 2005
Messages
21,125
Location
Cali
For the hood I trimmed where it was rubbing. A spacer will make it sit higher not lining up with the rest of the body.
Rails: fore rails. They are built to run with the crusher set up
Fuel: pump e70, it's the highest we have around here
Fuel system: not sure what "level" but it's all Fore parts. Twin 465s, return style, id1050x injectors
Standard whipple crusher t/b. For reference, mine is a gen 4 crusher
I think he meant the K member spacers that lower the engine.
 

2003RedfireVert

Male and Female He created them.
Established Member
Joined
Jan 25, 2022
Messages
2,374
Location
Fly over country
Fore system here, twin 450s, -8/-8, stock rails (dead headed setup), ford 80lb injectors. I’ll be close to 700w on E85. ~18lbs of boost on a kenne bell 2.8. Stock engine, exhaust, yada yada
 

V6&V8SHO

Well-Known Member
Established Member
Joined
Feb 15, 2005
Messages
1,367
Location
IL
Nice! Are you on pump gas or E85?

Could you share your mod list?

Return Style Fuel Sytem?

Dual Pump or Tripple Pumps?

Pump duty cycle % to hit 700?

My goal is to hit 800 + on a dyno.

My car will be stock long block engine (ford racing remanufactured longblock with a stamped build date of 2005), gen v 3.0 whipple, long tube headers 1-7/8", catless H pipe 3", catback exhaust 2.5", BA 2600 MAF, Twin Clutch, Fore Return Style Tripple Pump Fuel System, Strictly E85 , and I think that's it.


Like I said I originally wanted to go with ID1300x but was strayed towards the 1050x by my tuner as well as the vendors websites selling them now that I think of it I believe I also seen the disclaimer on Injector Dynamics downloadable excel file they have for compatibility reference.

What do you think ?

I had a reman ford block. Got about 8yrs out of it hammering on it before a spun rod bearing. 4yrs on a ported eaton at 17psi and 4yrs on a vmp tvs at 22psi. Pretty good.
 

MalcolmV8

Well-Known Member
Established Member
Joined
Mar 27, 2003
Messages
7,353
Location
Tampa, FL
The crusher inlet rubs on the hood but you can create some clearance. Here's how I did it some time back.

Here you can see area marked out to be clearanced and I had started cutting it.
AL9nZEUZ27fLFCZFfXjYub9uFpl4xjXRVn_8wqvoS4Hpkfl81ASCBI1-K5uYNuQxXxl5JsZg3VgqjpdACknN30pcpH_-uwqARQH3exynOEyAdL4EhrSTgna1hBCVhiz_vPYaqi_VBcWQt8DdnwA1ueNA1eAS=w640-h480-no


The hole cut open
AL9nZEUgoZsoCLyaeD_5n1siFvsmzDH8ZlTLJeNbV7MyGTZVvfgvsQ1KMouEUDHmLzZJLE_yxy9ui1849Rzax_s77nUZH4PdLkhJGkBKNNGr0uVSHCTaM6xunqwtfSM-ExA5X5FxaViMw6bNKWgVzJ7dV_ai=w640-h480-no


I then fiberglassed it in
AL9nZEUg4Vy5oU5lnKQcygWcb9RLudRHX7spppVoQDDuERADmVlz4HIHUfIJow7ST9E-Z3wfbT7EFEeTvkZ7tnD2--XNUid967wO4CCSI-1eLngnSdGIxrhFQdPtU_oFg1moBSoDbYSRcJhqPsl_G6IkCeLb=w640-h480-no


Since I was at it I smoothed out and filled all the other holes.
AL9nZEV9NfrJlNcLpQR1-L9H6_cI7kyy1mLP5jTGSK-dxG_Dpc1L8wy0hs3YE1C-dQZgPppnekT-DjZZcx_B4ikhmpDbP3tJRc5Aloy44480cDBHrAHAr8S6wRgSGlmjrrS7gC9NcOdgwroD_nSougABZxOl=w640-h480-no


After paint you can't even tell it was modified. It's like it was just made to fit a whipple
AL9nZEVfn46syM55FeHzwkgchQZ9FfgCgTExeIrI3Ooa4V27nYCTS3jCUGzucd76_7lkHJPPIRAu5_Gt4V0t9s8d85mkFPHjyLTF4p8mQS4eQ5Pt54zoStISo8wrPpjvfbLQSzzDgl7Ds0mroUhFqDqPyGBp=w800-h600-no


AL9nZEW681M9P6-lFL1uct_LkeT986Ngyth_0IRx0_33jcooYb_T5XRi6avsHDYTjEFLvQQtu7iESRX3RxeCK-4N2g_VbD0BuJgT3PztNj2HbIUiCyOC6Un2qj0hEvD6u9EKd1YrAsN-p0MlIYl3uQrLGMEj=w800-h600-no


Hope that gives you some ideas.

Malcolm
 

beefcake

Authorized Vendor
Authorized Vendor
Joined
May 16, 2001
Messages
8,969
Location
Cincinnati, OH
I think most questions are answered, if you need help with the fore or the blower, let me know as we have huge sales going for black friday

beef
 

Users who are viewing this thread



Top