on3performance single turbo kit install begin

[99riocobra]

True, I know it's typical for an auto turbo car to dyno low torque(and hp for that matter). Just enjoy it for sure!...And make some more videos

I know you probably mentioned it earlier in these 30 pages, but which turbo are you running now? Did you switch to the forward facing header setup?

 

[2002mustanggt]

True, I know it's typical for an auto turbo car to dyno low torque(and hp for that matter). Just enjoy it for sure!...And make some more videos

I know you probably mentioned it earlier in these 30 pages, but which turbo are you running now? Did you switch to the forward facing header setup?

Yeah forward facing on3 kit and Precision T70

 

[99riocobra]

Awesome, I thought I remembered you were switching over to the new setup...Is the precision a billet wheel or bb? Is it one offered through On3?

 

[2002mustanggt]

Awesome, I thought I remembered you were switching over to the new setup...Is the precision a billet wheel or bb? Is it one offered through On3?

I bought this turbo used from member at corral, just jb turbo , no billet or bb. I gain about 100rwhp with this turbo vs master power I used to run epper:

 

[99riocobra]

Awesome, precision is what I was leaning towards anyhow. What about running a 76mm, is there enough clearance for a bigger compressor size up front?

 

[2002mustanggt]

Awesome, precision is what I was leaning towards anyhow. What about running a 76mm, is there enough clearance for a bigger compressor size up front?

it;s a tight fit, T76 might fit might not or if you get smaller slim fan then it will be ok:beer:

 

[99riocobra]

Dang I was hoping it would fit no problem. I guess even on the Hellion kit the 76mm barely fits..

 

[2002mustanggt]

Went to track last night TNT, track was 111* temp hot as hell but still did 11.6 at 130mph with 2.0 60' and best to date 11.4 at 132mph with 1.99 60' . Converter is too tight , gets me only 1 psi boost off the tb, soon to get n20 just 50 shots to spool turbo off the line.

I have video on my 11.4 run that my friend posted on fb but don't know yet how to save to my pc so I can share them here.

 

[Turbo96]

132mph is low tens if you can get a good launch.

 

[2002mustanggt]

132mph is low tens if you can get a good launch.

Converter too tight, going to put small shots of n20 to spool turbo . Hoping to go low 10.

 

[2002mustanggt]

Install nos 38 jets to spool turbo , made 5 psi of boost on tb. Still was not happy and I knew some was up. I bought a boost leak tester and found sh*t load of boost leak from maf flange that was welded close to couplers , tps sensor and turbo it self. Now I don't need n20 to spool turbo , makes 14 psi of boost on tb , new track time and final number coming soon.......
Here are some video and pic

Big boost leak out of maf flange bolt hole
VIDEO0050.mp4 video by lvmustanggt - Photobucket

Boosting 14 psi in less then 5 sec on tb
[nomedia="http://www.youtube.com/watch?v=SXD-HdMeMJo"]Boosting with transbrake, 14 psi in less then 5sec - YouTube[/nomedia]
One more at night
[nomedia="http://www.youtube.com/watch?v=s2fbAIDLtOY&feature=related"]Boosting on transbrake. - YouTube[/nomedia]

Short ride with my girls
[nomedia="http://www.youtube.com/watch?v=Tm58OowWqTU&NR=1"]On3 FF turbo kit, precision t70 and built 4r70w - YouTube[/nomedia]
[nomedia="http://www.youtube.com/watch?v=SXD-HdMeMJo"]Boosting with transbrake, 14 psi in less then 5sec - YouTube[/nomedia]

 

[99riocobra]

Great job man, finding the source of a problem is much better than a bandaid...

Gotta ask, are you running the stock intercooler? Also are you running the wastegate open or recirculated?

 

[2002mustanggt]

Great job man, finding the source of a problem is much better than a bandaid...

Gotta ask, are you running the stock intercooler? Also are you running the wastegate open or recirculated?

Thanks man, it's been stress out few months but finally all the bugs worked out. Just upgrade to 4" think on3 race intercooler, I'm running new on3 44mm vband wastegate open.

 

[99riocobra]

I understand that for sure. Makes it all that much more rewarding huh.

Oh, so On3 offers a 4" thick intercooler? Does it fit right in the same spot beind the bumper suport? And I assume inlet and outlets are the same diameter/location?

 

[dwtjr3]

Wow man i havent followed a long this whole thread but you have a sick car. You still gonna run the nitrous?

And if you dont mind me asking roughly how much did it cost you to go turbo?

 

[2002mustanggt]

I understand that for sure. Makes it all that much more rewarding huh.

Oh, so On3 offers a 4" thick intercooler? Does it fit right in the same spot beind the bumper suport? And I assume inlet and outlets are the same diameter/location?

Yes they do offer 4" intercooler, much lighter then 3" I used to have and yes it fits good just like 3" once did.

 

[2002mustanggt]

Wow man i havent followed a long this whole thread but you have a sick car. You still gonna run the nitrous?

And if you dont mind me asking roughly how much did it cost you to go turbo?

Thanks !!! I might not use nitrous , but it's there so I might. After 10 psi of boost n20 shuts off automatic, it's setup that way.

 

[99riocobra]

Yes they do offer 4" intercooler, much lighter then 3" I used to have and yes it fits good just like 3" once did.

Great to know :beer:

So with the leaks fixed do you notice a quicker spool when getting on it on the street from a roll and whatnot as well?

 

[2002mustanggt]

Great to know :beer:

So with the leaks fixed do you notice a quicker spool when getting on it on the street from a roll and whatnot as well?

Yes sir , it went from 1 psi boost on tb to 14 psi so you beat spools fast
Now it spools too fast lol

 

[2002mustanggt]

Going to track tomorrow, wish me luck.