Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Mustang Forums
2011-2014 Mustangs
Exhaust
Installed Kooks Shorty Headers
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="StalkerStang" data-source="post: 15548001" data-attributes="member: 160824"><p>Finished these yesterday along with doing the clutch. I did the headers first, before I dropped the tranny to do the clutch. After reading how involved and what a nightmare headers can be on these...... its really not that bad. Mine might have been a tad easier because they were shorties, but I can't see them being that different than doing LT's other than needing more vertical clearance. I did do this with a jack and jackstands in my garage, with no power tools. Now I'm not saying it was cake, but very do-able. Here are some things I did have issues with.</p><p></p><p>The front most bolts for the engine mounts (the aluminum ones that bolt directly to the engine) are a bit of a pain to get to, especially the passenger side one.</p><p></p><p>Not hard but tedious: all the factory header nuts are pretty much tight all the way out. A 1/4 drive ratchet and socket comes in handy, and a ratcheting wrench does too.</p><p></p><p>I was not able to re-use all the factory studs. I wanted to, but time and space constraints just made it easier to use the bolts that come with the headers.</p><p></p><p>Again, tedious and time consuming, tightening all the header bolts/nuts. Some from the top and some from the bottom. Back and forth.</p><p></p><p>Lastly, if you use the factory mid pipe (like me lol), the passenger side outer most stud that bolts to the header is a NIGHTMARE! It is nearly impossible to use the factory stud and nut here..... there is simply no room for most any tool to tighten the nut and it is not accessible from the top like the factory headers are because the tubes route differently and block access to the area. I ended up knocking the stud out and replacing it with a bolt and lock nut, BUT, that is not the end of the nightmare. Because the factory cat is so large and close to the header flange, it is almost as impossible to get to. I ended up using a curved wrench to hold the bolt from the top and a crow foot open end with a 3/8 ratchet and extension to tighten it a 1/4 turn at a time lol! Not fun.....</p></blockquote><p></p>
[QUOTE="StalkerStang, post: 15548001, member: 160824"] Finished these yesterday along with doing the clutch. I did the headers first, before I dropped the tranny to do the clutch. After reading how involved and what a nightmare headers can be on these...... its really not that bad. Mine might have been a tad easier because they were shorties, but I can't see them being that different than doing LT's other than needing more vertical clearance. I did do this with a jack and jackstands in my garage, with no power tools. Now I'm not saying it was cake, but very do-able. Here are some things I did have issues with. The front most bolts for the engine mounts (the aluminum ones that bolt directly to the engine) are a bit of a pain to get to, especially the passenger side one. Not hard but tedious: all the factory header nuts are pretty much tight all the way out. A 1/4 drive ratchet and socket comes in handy, and a ratcheting wrench does too. I was not able to re-use all the factory studs. I wanted to, but time and space constraints just made it easier to use the bolts that come with the headers. Again, tedious and time consuming, tightening all the header bolts/nuts. Some from the top and some from the bottom. Back and forth. Lastly, if you use the factory mid pipe (like me lol), the passenger side outer most stud that bolts to the header is a NIGHTMARE! It is nearly impossible to use the factory stud and nut here..... there is simply no room for most any tool to tighten the nut and it is not accessible from the top like the factory headers are because the tubes route differently and block access to the area. I ended up knocking the stud out and replacing it with a bolt and lock nut, BUT, that is not the end of the nightmare. Because the factory cat is so large and close to the header flange, it is almost as impossible to get to. I ended up using a curved wrench to hold the bolt from the top and a crow foot open end with a 3/8 ratchet and extension to tighten it a 1/4 turn at a time lol! Not fun..... [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Mustang Forums
2011-2014 Mustangs
Exhaust
Installed Kooks Shorty Headers
Top