*FS* Like New Borla XR1 Catback. (STAINLESS Mufflers) Need to sell ASAP!!

HandsomeRob

Active Member
Established Member
Joined
Jul 20, 2009
Messages
2,975
Location
Los Angeles C.A.
*SOLD* Like New Borla XR1 Catback. (STAINLESS Mufflers) Need to sell ASAP!!

Hey SVTP,
I'm selling my barely used like new condition 2.5" Borla XR1 Catback.
The tailpipes are designed to dump right before the fuel tank for that "Clean No Tailpipe look" (Needs custom hangers installed)
You can add the rear tailpipe section if you take it to an exhaust shop for those of you who like exhaust tips.
Catback has stainless hangers as well.
Less than 200 miles. Car is garaged.
This exhaust sounds absolutely WICKED. Very Loud!!
I'm selling because my new built 750HP motor needs a 3" exhaust.
I plan on running 3" Borla XR1's which is why I'm selling my current 2.5" exhaust setup.
I originally paid $150 each muffler plus shipping from Summit Racing and $300 to install it and fab up some tailpipes and collectors.
I paid a total of $640 for this Catback.
My loss is your gain.
SOLD!!
Thanks
Rob

00D905F1-C38D-4C5B-A249-33B5FE363C0D-138-00000002DA97769A_zpsec748362.gif


A35E9790-C857-4053-BCEE-4C2564243ED1-138-00000002EC6D0496_zps01574842.gif


4AE9282A-6830-4405-9525-0928E32992CB-138-00000002E4A51CDE_zps2f3674c8.gif
 
Last edited:

Rosco

Member
Established Member
Joined
Nov 17, 2012
Messages
118
Location
La Verne, CA
How's it going Rob. Im really interested in these mufflers. I would like to weld them in the stock catback, but im not sure if/what pipes i would need from your system. I'm located in the LA area and I'm willing to pick up. Would you be willing to sell just the mufflers.
Thanks, Mike.
 

1hot281

Active Member
Established Member
Joined
Jul 1, 2009
Messages
1,942
Location
The States
How's it going Rob. Im really interested in these mufflers. I would like to weld them in the stock catback, but im not sure if/what pipes i would need from your system. I'm located in the LA area and I'm willing to pick up. Would you be willing to sell just the mufflers.
Thanks, Mike.

This catback looks to be 2.5" tubing with 2.5" inlet/outlet mufflers... and your stock catback is 2.25" piping and mufflers. I wouldn't weld these mufflers in to your stock catback. Almost everything is here to replace your stock catback. The flow tubes from the midpipe, the mufflers, the over axle pipes... all you need are 2.5" tailpipes and whatever tips you want.
 

Rosco

Member
Established Member
Joined
Nov 17, 2012
Messages
118
Location
La Verne, CA
This catback looks to be 2.5" tubing with 2.5" inlet/outlet mufflers... and your stock catback is 2.25" piping and mufflers. I wouldn't weld these mufflers in to your stock catback. Almost everything is here to replace your stock catback. The flow tubes from the midpipe, the mufflers, the over axle pipes... all you need are 2.5" tailpipes and whatever tips you want.

I thought the stock system was 2.5, but I looked it up and your right, haha it won't work out very well. Can I bolt this up to the stock mid pipe with just a reducer? And then get the tail pipes.
 

sgilbert8277

New Member
Established Member
Joined
Sep 1, 2012
Messages
65
Location
Norfolk, va
would you be willing to separate the Mufflers from the the cat-back? I have a IRS cobra and just want the mufflers? 23511, Norfolk VA...
 

Users who are viewing this thread



Top