Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
The Terminator
Driveline
Clutch quad/Firewall adj. install tips needed
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="black03" data-source="post: 1085725" data-attributes="member: 4037"><p><a href="http://www.shane.roberts.net/quad.htm" target="_blank">http://www.shane.roberts.net/quad.htm</a> </p><p><a href="http://www.azdroptop.homestead.com/...allInstall.html" target="_blank">http://www.azdroptop.homestead.com/...allInstall.html</a> </p><p><a href="http://www.steeda.com/instructions/doublehook.htm" target="_blank">http://www.steeda.com/instructions/doublehook.htm</a> </p><p>I have the URP Triple hook quadrant and UPR firewall Adj.</p><p>I personally followed the steeda directions. When I replaced the quadrant I did not reuse any of the springs on the stock setup or any at all, just the pin to hold the quadrant in place. Also I used a dremel to saw the plastic piece off of the stock firewall adj. . do the quadrant first and use the second hook cause the 3rd does not fit. Also when the firewall adj. is ready to be installed it is easier to have both pieces of the upr adj. screwed together set it in place in the firewall. so that when installed it fits in between the engine and firewall, and gives you enough space to srew it in. As far as the missing screws I think you can use and old screw thats about 1/2 to 3/4 inch long. I used the two upper holes of the firewall adj. becuase its impossible to screw in the bottom one. Use a drill to start a hole for the upper right hole. Hope this helps. If you need anything else just pm me. Good luck , Jared. </p><p></p><p>--------------------------------------------------------------------------------</p></blockquote><p></p>
[QUOTE="black03, post: 1085725, member: 4037"] [url]http://www.shane.roberts.net/quad.htm[/url] [url]http://www.azdroptop.homestead.com/...allInstall.html[/url] [url]http://www.steeda.com/instructions/doublehook.htm[/url] I have the URP Triple hook quadrant and UPR firewall Adj. I personally followed the steeda directions. When I replaced the quadrant I did not reuse any of the springs on the stock setup or any at all, just the pin to hold the quadrant in place. Also I used a dremel to saw the plastic piece off of the stock firewall adj. . do the quadrant first and use the second hook cause the 3rd does not fit. Also when the firewall adj. is ready to be installed it is easier to have both pieces of the upr adj. screwed together set it in place in the firewall. so that when installed it fits in between the engine and firewall, and gives you enough space to srew it in. As far as the missing screws I think you can use and old screw thats about 1/2 to 3/4 inch long. I used the two upper holes of the firewall adj. becuase its impossible to screw in the bottom one. Use a drill to start a hole for the upper right hole. Hope this helps. If you need anything else just pm me. Good luck , Jared. -------------------------------------------------------------------------------- [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
The Terminator
Driveline
Clutch quad/Firewall adj. install tips needed
Top