Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Mustang Forums
2011-2014 Mustangs
Driveline/Suspension
Adjustable UCA question
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="Gpcalero" data-source="post: 16406219" data-attributes="member: 155311"><p>Slow Poke, I googled this in 30 seconds. </p><p></p><p>Space is tight yes. But on my BMR UCA I am still able to adjust it. </p><p></p><p>KTA141 – S197 Mustang Adjustable Upper Control Arm and Mount Kit Includes: • Pinion Angle Adjustable Arm • Mount • M14 x 60mm Bolt • M14 x 25mm Bolt • M16 x 45mm Flanged Bolt • M14 Nut • Spring Washer – Qty 2 Tools Required: • Socket Wrench • 20mm Socket • 15mm Socket • 13mm Socket • 21mm Wrench – Qty 2 • Wrench or Socket WARNING: Whiteline Products are designed for easy installation however professional installation by a Whiteline Performance Center is recommended. Please drive carefully and accustom yourself to the improved handling characteristics of the vehicle. 1. Lift the vehicle and place jack stands under the chassis (not rear axle). 2. Remove the lower section of the rear seat by releasing the two lower clips located and the front of the seat bottom. Push back the on the seat and when the clips are released, lift the seat and remove. This will allow access to the upper retaining bolt. 3. Remove the mount retaining bolt. 4. From below the car, remove the upper control arm bolt to mount bolt. 5. Remove the upper control arm bolt connected to the axle. 6. Remove the 2 remaining control arm mount bolts. 7. Properly support the gas tank and remove the two rear bolts securing the tank straps. Lower the tank approximately 2 inches to allow clearance to remove the OE bracket. 8. Prepare Whiteline Arm and Mount for installation by adjusting pinion angle of eccentric crush tube to desired position. Then tightening the lock nut up against the mount. 9. Bolt the mount to the car using the lower factory bolts and tighten to 110 ft lbs. 10. Insert the supplied M16 bolt and washer into the upper front hole located inside the car and tighten to 129 ft lbs, then reinstall the rear seat. 11. Reinstall fuel tank strap bolts and tighten to 33ft lbs. 12. Jack up rear end until the control arm mounting holes line up to the axle mount and reinsert bolt. 13. Double check to ensure all bolts have been re-tightened and lower vehicle. For specialist assistance in North America: Website: <a href="http://www.WhitelineUS.com" target="_blank">www.WhitelineUS.com</a> Email: <a href="mailto:Support@WhitelineUS.com">Support@WhitelineUS.com</a> Phone: (909) 476-2860 All other countries please email <a href="mailto:Support@Whiteline.com.au">Support@Whiteline.com.au</a></p></blockquote><p></p>
[QUOTE="Gpcalero, post: 16406219, member: 155311"] Slow Poke, I googled this in 30 seconds. Space is tight yes. But on my BMR UCA I am still able to adjust it. KTA141 – S197 Mustang Adjustable Upper Control Arm and Mount Kit Includes: • Pinion Angle Adjustable Arm • Mount • M14 x 60mm Bolt • M14 x 25mm Bolt • M16 x 45mm Flanged Bolt • M14 Nut • Spring Washer – Qty 2 Tools Required: • Socket Wrench • 20mm Socket • 15mm Socket • 13mm Socket • 21mm Wrench – Qty 2 • Wrench or Socket WARNING: Whiteline Products are designed for easy installation however professional installation by a Whiteline Performance Center is recommended. Please drive carefully and accustom yourself to the improved handling characteristics of the vehicle. 1. Lift the vehicle and place jack stands under the chassis (not rear axle). 2. Remove the lower section of the rear seat by releasing the two lower clips located and the front of the seat bottom. Push back the on the seat and when the clips are released, lift the seat and remove. This will allow access to the upper retaining bolt. 3. Remove the mount retaining bolt. 4. From below the car, remove the upper control arm bolt to mount bolt. 5. Remove the upper control arm bolt connected to the axle. 6. Remove the 2 remaining control arm mount bolts. 7. Properly support the gas tank and remove the two rear bolts securing the tank straps. Lower the tank approximately 2 inches to allow clearance to remove the OE bracket. 8. Prepare Whiteline Arm and Mount for installation by adjusting pinion angle of eccentric crush tube to desired position. Then tightening the lock nut up against the mount. 9. Bolt the mount to the car using the lower factory bolts and tighten to 110 ft lbs. 10. Insert the supplied M16 bolt and washer into the upper front hole located inside the car and tighten to 129 ft lbs, then reinstall the rear seat. 11. Reinstall fuel tank strap bolts and tighten to 33ft lbs. 12. Jack up rear end until the control arm mounting holes line up to the axle mount and reinsert bolt. 13. Double check to ensure all bolts have been re-tightened and lower vehicle. For specialist assistance in North America: Website: [URL="http://www.WhitelineUS.com"]www.WhitelineUS.com[/URL] Email: [email]Support@WhitelineUS.com[/email] Phone: (909) 476-2860 All other countries please email [email]Support@Whiteline.com.au[/email] [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Mustang Forums
2011-2014 Mustangs
Driveline/Suspension
Adjustable UCA question
Top