FOR SALE: 2004 Torch Red Turbo Mach 1 w/ fully built motor and 4r70w

chernandez88

Member
Established Member
Joined
Jun 2, 2009
Messages
112
Location
Miami
Hey all! Finally decided to put my 2004 Mach 1 up for grabs. I bought this car back in 2006 with 19k miles. Current miles on the odometer is 34k. Engine and transmission have about 600 miles since it was built. Has A/C and power steering. The car made over 800hp at 17 psi on a very conservative tune with plenty of room to make over 1000hp. This car was built with high end parts and you will not be disappointed. Reason for selling: I'm in third year medical school and haven't been using the car, nor barely have the time. I would rather use the money to pay for some of my loans. Asking price is 25k obo. Below I will include almost all the mod list, I'm sure I may have forgotten a thing or two. If you have any questions please message me and I will try to get back to you as soon as possible since I am studying for my first board exam. Thank you.

Engine:
-New Ford Performance M-6010-A46NA Aluminum block
-DSS Racing 4.6/5.4 Main Support system with 3/4 billet aluminum w/ custom ARP main studs
-DSS ARP kit 8mm outer studs, nuts and washers to complete main set
-CP Piston, custom coated, weighted and balance
-Kellog forged crankshaft
-Oliver 5.933” I-beam rods
-Clevite engine main bearings
-MMR girdle
-Full ARP bolts on engine
-FRP high flow water pump
-Melling cobra oil pump
-Fox Lake Stage 5-axis 3 CNC ported heads w/ bronze guides + oversized hardened seats
-ARP head stud kit
-Ferrea SS valves w/ ferrea SS valve spring seats
-Bullit Custom Turbo cams
-Comp camp High Load Beehive Valve springs
-Accufab twin 60mm throttle body
-Ported upper & lower intake manifold
-MMR Street/Strip 7 QRT Oil pan
-MMR Coolant and Oil filter AN fitting relocation kit.
-Brand New ford racing 4v timing chain kit
-Brand New Ford Racing Coils
-Brand New Engine harness
-Energy Suspension motor mounts
-Canton oil catch can w/ fragola braided lines and custom AN fitting welds on valve covers
-Engine has all new sensors including water temp, oil, etc.
-New Power steering rack w/ upgraded high pressures lines to -4AN Fragola Teflon braided lines and fittings
-Canton Power Steering reservoir

Powertrain:
-Built 8 clutch 4r70w w/ billet input shaft.
-Circle D 3400 stall converter.
-FB Performance Manual Valve body w/ Lock up, Overdrive and Transbrake.
-B&M 70298 Hi-Tek Heavy-Duty Transmission Cooler w/ fan
-B&M 81001 Hammer shifter
-Ford racing 31 Spline aluminum driveshaft
-Energy suspension transmission mount

Fuel:
-Return style fuel system
-Injector dynamics ID1300 custom coated red caps
-Fore Innovation redesigned fuel rails
-Magna fuel 750 pump (Sent 2 months ago to rebuilt and pressure tested by Magna Fuel)
-Aeromotive 13132 Extreme Flow fuel pressure regulator
-Dual feed sumped fuel tank w/ custom coating/sealed
-10AN Fragola PTFE Teflon braided steel feed line
-8AN Fragola PTFE Teflon braided return line
-74 Micro steel element reusable fuel pump pre filter
-25 Micro steel element reusable fuel pump post filter


Power Adder:
-Borg Warner S482SX T4 Race Cover edition with custom welded V-band & K&N 5 inch filter (rated for 1300+)
-Custom 3.5” Downpipe with Electric cutout
-4 inch Intercooler.
-Tial 44mm Wastegate
-Tial 50mm Blow off valve
-New Cold side with v-band and custom coated wrinkled black
-Pmas HPX Slot sensor w/ plug and play harness kit

Cooling:
-Mishimoto Aluminum radiator w/ custom AN fittings welded
-MMR Coolant crossover delete kit
-Custom made coolant tank reservoir with welded AN fittings
-Lincoln Mark 8 Fan with custom wiring harness.

Suspension:
-Tubular QA1 Front crossmember
-Tubular QA1 A-Arm
-Steeda Front coilover kit w/ 200 lb spring
-New Tokico D-spec adjustable Front Strut
-Steeda 4-bolt Billet camber kit
-Steeda full length subframe connector w/ brace
-UPR full rear suspension(not installed)
-FR500 black chrome 18x10 Rear Wheel on Nitto Drag radials
-FR500 black chrome 18x9 Front wheels on Michelin pilot sport
-Front and Rear Drilled & Slotted Rotors w/ Hawk pads and stainless steel brake line upgrade

Electronics:
-Turbosmart Eboost 2 Turboost controller
-AEM UEGO wide band
-Battery relocated to trunk with Premium copper 2/0 Positive wire, 1/0 Negative wire and billet optima battery tray
-Brand New Optima Red top battery
-Big Three wire upgrade
-Custom accessories fusebox w/ on/off cutoff
-Leash Single 70 amp relay board w/Fuse for fuel pump.
-Leash Dual 70 amp relay board w/fuse for fan controller. Fans are controlled by the cars computer.
-New PA performance 200 amp upgrade w/ sense wire relocated to battery
-SCT ITSX tuner
IMG_1418.jpg IMG_1419.jpg IMG_1415.jpg IMG_1419.jpg img_1413.jpg IMG_1420.jpg IMG_1881.jpg IMG_1887.jpg IMG_1885.jpg IMG_1888.jpg
 

chernandez88

Member
Established Member
Joined
Jun 2, 2009
Messages
112
Location
Miami
Bump. The Mach 1 is still available. A well built race car with the drivability of a daily driver. Forgot to disclose that it makes 700Hp on pump gas at 13 psi.
 

gimmie11s

I Race Pontiacs
Established Member
Premium Member
Joined
Jun 1, 2004
Messages
18,488
Location
la la land
Wow... SHIT TON of car for $25k. Thank God you dont live in SoCal.. i'd be sleeping on the couch right now.

GLWS!
 

Bronco2Fan

New Member
Established Member
Joined
May 24, 2021
Messages
21
Location
Texas
Really beautiful Mach 1. As said, if your were closer it would be in my Garage already. I'd love to have it. If no one bites i may have to fly to Fla.
 

Users who are viewing this thread



Top