drivetrain

A few more pallets of Driveshaft Shop just showed up here at Lethal Performance. No wait needed, let's beef up that drivetrain today! This does include the T56 magnum shafts. Message me and we'll go over what's readily available. www.lethalperformance.com

A few more pallets of Driveshaft Shop just showed up here at Lethal Performance. No wait needed, let's beef up that drivetrain today! This does include the T56 magnum shafts. Message me and we'll go over what's readily available. www.lethalperformance.com

My stocker throw-out bearing is on its way out, and that’s one job I think I’ll pass on to the pros. Since my 2010 has 62,000 and a VMP Gen 2 I’m going to go ahead and do the clutch also. Does anyone know of a shop in the Houston area I can trust? There’s gotta be one Shelbys in the area...

I am currently swapping this 2007 GT with a 2008 GT500 drivetrain, I will basically have a complete car for sale between this '07 and the '06 GT that I have. I am not 100% sure on what everything goes for when it comes to these parts so I am up for offers on about everything on the car from...

Hi there, I have been having what I believe to be an issue for quite some time now. However, I am not sure due to not being familiar with specifically how GT500s are supposed to shift. I occasionally have shifts that dont smoothly engage, but they also dont grind; it's more as if it skips into...

Hi all, This is the stock 2010 GT500 2-Piece driveshaft that I am selling. I removed it to install a one piece aluminum shaft, no issues with the stock shaft as far as I could tell. Looking for $150 OBO + buyer pays shipping (could be around $40).

Hi all, I've got a 2010 GT500 with about 60K miles on the car. I've been noticing a vibration that is both felt and extremely audible from outside of the vehicle. The noise is most prevalent in 3rd and 4th gear and usually at about 1800-2000 rpm under heavy load. I have only really noticed the...

Challenge Accepted Sam Anderson challenged himself to build a 733-horsepower classic Mustang By Steve Turner Photos courtesy of Sam Anderson If you have built more than one project car, you always want to push the next one to a higher plane than the last. That was definitely the case for...

Alright sooo....I recently just fixed a vibration that I found out to be a bad factory UCA on my 2012 GT. Which ended up damaging my 1 pc driveshaft's yoke I had on there... But before I did that I had gotten new wheels and tires from American Muscle and upgraded to a set of brembos in the...

Looking for a complete donor car with a solid drivetrain for my 01. Looking for something with less then 75k miles but will consider higher mileage if the price is right. Coupe/convertible or color doesn't matter. Will also consider buying only the drivetrain conversion with all wiring...

As title says, I'm looking to buy an aluminum driveshaft with included install hardware.

I have a few clutches and flywheels for a 99-04 2v manual. Prices arent firm, txt for pics. 918-859-6565 Stock 02 GT Clutch w/ 16k miles: $100 + shipping Stock 02 GT Flywheel w/ 16k miles: $50 + shipping, needs to be resurfaced Stock 00 GT Flywheel w/ 95k miles: $50 + shipping, needs to...

I bought this thinking i needed for a cobra I purchased, however it already had one installed. Save you $35+ buying this one. Ships to US (all 50 States ONLY) unless you wanna kick in the extra. This one is RED Powdercoat. Lets just say the IRS Brace from Billetflow is the BEST insurance you...

I am looking for the best bang for the buck aluminum flywheel for my 03 cobra. i was gonna get either the fidanza- Fidanza Flywheel - Aluminum FORD MUSTANG GT; BULLITT; MACH 1; COBRA 1996 - 2004 4.6 186481 or the ram- 1996-11 Mustang Ram Billet Aluminum Flywheel, 8 Bolt at LRS - Same Day...

3.55 Ring and Pinion have 3,200 miles of use. Vehicle recently upgraded to a Shelby Super Snake $100 OBO + Shipping