2008 GT500 Vista Blue destriped.
80k miles. 30k on built motor.
$26,000
Performance:
Tuned by Bob Kurgan
740/740 on e85
680/640 on 93
Brand new Gen 3 2.9 Whipple w/ 3' pulley
10% innovators harmonic balancer (19lbs)
93 and e85 Tunes
9.1 compresion
GT cams
20 thousands bore
Manley rods and...
I have some parts for sale from a 2003 cobra with 49,000 miles that I am parting out. All prices are plus paypal fees and shipping.
Front Bilsteins - $95
Front Calipers and Rotors - $300
Front H&R springs - $95
Factory Radio - $100
I have tons of DOHC timing chain, lash adjuster, cam followers if you need something not listed PM me I may have it!
Lets start with the following:
Lot No 1 Used DOHC Set ~ 3,000 Miles Asking $225 obo Shipped via USPS
As in 2 engine pics below, getting ready to remove from running 97 Cobra...
Looking to sell in Denver metro area. $13,500. I'm moving very soon and looking for a new home for her and i have two young kids so she's not getting driven much at all. 21k miles. It was in an accident (~12 years ago) and the front left end was rebuilt so it is a salvage title. Have all...
I bought this full set because I was going to put them into my '96. Changed my mind so now these are just sitting.
Charcoal grey with grey inserts.
Tear on the drivers side bolster, see picture. Also a mark on the passenger seat, near the top. Could use a good, general cleaning as well.
Would...
**SOLD**
2004 Screaming Yellow Ford Mustang Cobra SVT Convertible. Located in Murphy TX (DFW area). VIN: 1FAFP49Y04F195094
85K miles - non-smoker - one owner - always garaged. I have all the documentation since the car was new. It has always had stock tune and pulley - never been to the...
Original 10 spline input shaft for t56. Pulled from my 2004 cobra when I upgraded to 26 spline. A lil over 32k miles on it. Comes with both bearings and races, all in perfect shape.
$60 shipped (to lower 48)
Call or text for more pics/info/questions. Thanks!
Dan, 240-971-9013
Hello everyone,
I am getting code P0135 (Bank 1 sensor 1 heater circuit malfunction) on my Mach 1. I have Mac longtubes, off road x pipe, and dumped spintech mufflers. I also have new NTK O2 sensors upstream. I have a bama tune. I have told them about the code, and they increased delay for bank...
03-04 Mustang Cobra front bumper. Brand new never used. If your reading this post it’s available. Only took out of packaging to take the picture. Comes with bumper, brackets and rivets. Price firm! $200. If you want the whole package bumper, brackets, rivets, bezels and fog lights all brand new...
Couple Dig runs from this past weekend cars and mods listed below. I must say the 392 and 6th gen held there ground against the boosted cars. Boosted cars were both on drag radials, 392 and 6th gen were on street tires.
630ish 13-14 Gt500
580ish rwhp LSA 5th gen
Stock 392 Dodge Charger
Stock 6th...
I got a 03 oxfard white cobra and ive been wondering what i need to do to get it to 600 hp or so, i bought a 2.3 whipple supercharger and a whipple crusher throttle body would that be enough? what fuel mods do i need in specific to help with my setup, im also running catbacks and a jlt cold air...
This Ford Performance Off-Road Sparco Steering Wheel was originally meant for 2005-2019+ Mustangs but with a few parts from NRG Innovations it can be retrofitted into 94-98 SN95 and 99-04 New Edge Mustangs!
Ford Performance Sparco Steering Wheel [Part # M-3600-RA]
American Muscle: Ford...
Finally ditched the Rovos after two years. They had a good run.
Wheel Specs for Varrstoen ES9
Finish: Hyper Black
Front: 18 x 9.5 +22 w/ 275 35 R888R
Rear: 18 x 10.5 +22 w/ 305 35 R888
The rear has a 3/4" MM Hubcentric Spacer and ARP extended studs. The rear fenders have been rolled and I...
My Cobra has been having some problems where it won't hold idle and bog down, but I adjusted the throttle blade to be open a little bit more. And it seemed to hold after I revved it, I just don't know what these numbers man. Does anyone know anything about these numbers? is this normal? Anything...
Hello,
I have a 1996 Cobra with 17k miles. It seems as though the 2nd gear synchro has gone bad because it grinds at high revs with quick shifts (Not power shifting or even partial throttle). It has a B&M short throw shifter (Not sure if this could be part of the problem). Is it worth getting...
I have 4 AFS 18" Machined style wheels for sale, they are 9" in the front and 10.5" in the rear. They are in MINT condition, also have 2 coats of ceramic coating on them for protection and shine. I am willing to ship, $999 Shipped, Text me for any questions (810) 343-3067
Has anyone done or seen custom upholstery in a terminator or new edge in general? Like Alcantara or leather on the dash or replacing the plastic door trim.
**Sale is now Pending** :(
Damn I hate to even post this, but here it is :( I have posted a ton on here, search my name let me know if you have any questions or want pictures of anything etc.
For Sale:
2003 Cobra Convertible
Redfire Exterior Color
Black cloth top
Black interior with Gray...
Ok, so I need to get my car on 4 jack stands so I can drop the irs, and put rotors on the front. I did the clutch last week on a lift and used the jack points (pinch welds) but I will not be doing this on a lift.
Since jack stands are "U" shaped I don't believe they can be used at the pinch...
Looking to buy a 03-04 mustang cobra. Looking for high mileage or rebuilt tittle. Location is not a problem I will be willing to travel for right deal.
I am new to this website so bare with me. I’m just looking to own my first terminator. Thank you all.