Search results

Almost new H&R race springs with isolators and maximum motorsports sport 1 rear shocks off a SRA. Located in Port St Lucie Florida. Springs 350 shipped Shocks 300 shipped

Who else have received an email from VMP with this technical Bulletin? So now we need to remove the supercharger and inspect if the intercooler is damaged and then add the new support rails. Who is going to pay for the disassembly and or time that this will take to fix a defect in their...

2007 Roush 500RC truck is in good shape. Got new rear shocks, JDM tune, 16-in wilwood front brakes, JL speakers and sub, lowered 2 inch in the front and 5 in the rear, has slam air bags on the rear for lift assist when hauling trailer or heavier load, has inboard air compressor, sunroof...

I just swapped out injectors and now I am blowing the Maxi 26 fuse. If I unplug the harness that goes to the ccrm it doesn't blow,as soon as I plug it back in it pops. Is this a clear sign the CCRM is bad? What else can I check? I showed the harness unplugged and the Maxi below.

Injectors were used for less than 150 miles. Just removed yesterday. I ran E85.$600 shipped within the US.

Injectors were used for less than 150 miles. Just removed yesterday. I ran E85.$600 shipped within the US.

I am trying to figure out the intercooler pump wiring and need some help. I think #1 goes to a constant power and #3 is power to the pump but what one is the trigger and what is the other terminal for?

Brand new never installed lfp Terminator heat exchanger. Comes with two new hoses and hose clamps. 325 shipped.

Brand new never installed lfp Terminator heat exchanger. Comes with two new hoses and hose clamps. 325 shipped.

I have a bunch of parts off my 04 cobra with a little over 46000 miles. All prices include shipping. I'm also open to offers. I'm located in Port St Lucie Florida if you rather pick up. Oil pan = 80 Dip stick = 75 Cams= 250 Blower and elbow = 750 Intercooler = 300 Stock injectors = 100

I ordered a new roush tensioner to replace my oem tensioner. I swap the pulley and the oem cobra pulley doesn't set all the way down onto the new roush tensioner. Is this right? Do I need to add washers between the engine and back of the 3 tensioner bolts? The oem has a .4195" shaft for the...

I have brand new never used MMR coolant crossover delete with lines and no filler and filler neck option. $390 shipped I also have a MMR coolant crossover plug. $20 shipped

I have two sets brand new in box of Ford Performance Powered by SVT coil covers. $95 each shipped within the US.

I'm selling the complete motor, kenne bell 2.1 supercharger, with big air tube, bbk shorty headers, , newer flywheel. Motor has just over 38,xxx miles, new LFP heat exchanger, 04 cobra heat exchanger brackets, k-member. Motor internals are stock. We are pulling the motor out in about 4 weeks...

Original 28 spline axles with 38xxx miles $120 373 gears 5xxx miles I think Ford racing. $100 Original posi differential 28 spline 38xxx miles. $150 local New MMR billet oil pump gears mmr-404350. $150 shipped Parts are all located in port st lucie Florida.

17x10.5 rear rims and 18x5 front rims. Front and rear tires are only a couple months old. As you can see in a pix there is a small area that has curb rash, can't tell from a distance. Also have an extra set of front tires included that are in great shape. Asking $1100. Located in Florida 92...

I have purchased a new Kit from a guy but don't have any Directions, does anyone have a set I can copy or that you can email me?

Just what the title says. Im located in Texas. Pm me if you have one you would like to sell. thank you Matt

Just wanted to let everyone know that Gearheads in Arlington tx ROCK!!!!! I dropped my mustang off to have them to install a kenne bell 2.1 and clutch and they are awesome!! Great costumer service and going above and beyond to make the customer happy!!! Travis and Matt are great to work with!!!!

Got me coming.

What is the best way to run the electrical wire for the fuel pressure gauge and the vac line for the boost gauge (thru the firewall)? i have looked and there is really no open holes in the firewall of my 04 mustang. Please let me know what you guys have done.

I need the sub mounting brackets for the mach 1000 subs. Does anyone know where i can get them or does any one know the part number? Or does anyone know how to fab your own? Thanks for your help. Matt

i have a 2006 trx 450r that is set up for cross country racing. The motor is a 470 stroker with about 50hrs on it. has elka quad rated long travel front and rear shocks. houser max ground clearance a-arms, elka system 5 steering stab, flexx handlebars, twist throttle, quad tech seat, FMF full...

I am looking for a white face roush cluster that will fit a 2004 gt V8. please pm or email me at [email protected]