While resetting throttle stop this weekend I broke the end on the cruise control cable. Do they sell just the end for replacement or do I need a full cable?
Let me know what you got.
Thanks
Anyone have access to stock or semi stock NA 4v tune for HP tuners? Or would be able to read one? HPTUNER forums are pretty worthless so far.
Working on my 2001 Cobra tune now and would like to compare, I no longer have a stock tune and do not wish to take to dealer to flash stock tune.
Got...
Looking for rear bumper side markers also would like headlights let me know what you got.
Wouldn't mind harness section of the headlights as mine are damaged broken clips.
Any remote tuners out there using HPTuners yet?
Old tuner says he can no longer tune my 2001 cobra with SCT software. But I have the MPVI2 for my 300 so can drop tunes in the Cobra using it.
So recently I pulled the motor and sent to BB&T for head work and new pistons and rings. Motor was assembled, degreed, and installed.
I also went through wiring hardness and re-wrapped and replaced any broken retaining clips (mainly on injector wiring harness and O2 harness) The clips were...
This is how it currently sits.
Is there a performance red powder out there? Or am I stuck going with a wrinkle black finish?
What other color options do you guys think will look good?
Looking to get 2 17x9 wheels cobra/cobra rs etc... doing a cheap drag set for my Cobra and my SRT8.
As long as no bends or cracks I will take them.
I am located in West TN and prefer local. PM me please
So long story short tire place jacked up my h-pipe and cat-back they are replacing the h-pipe but will not replace the cat-back as it had some previous scrap damage.
Looking for a Stainless setup that I can polish out let me know what you got? Local to Tennessee or shipped to 38008...
Finally got a chance to take the 300 to the local drag strip last night for test n tune. Only about 20 cars there and track was well prepped. Most cars were true drag cars running in 5s-6s.
Street cars where my car(2013 300SRT8,fully loaded mods CAI,canned Tune), a 2010 gt auto(full...
2001 Cobra 95K miles
Performance Red - ES
1 of 226 built
asking $15500
Located in West Tennessee. Jackson, TN
Engine -- Professionally built and rebuilt lol
5.1L Forged Aluminum Block 11 to 1 compression-- Rated to Handle 900 HP
Probe Industries Forged Crank
Ultra Light Weight Forged I-beam...
Well finally got the cobra motor back in after a rebuild caused by defective main timing chain, it was a full cloyes 4v kit so make sure you fully inspect the chains...
Anyway after sitting for 2 almost 3 years the fuel pump decided to take a dump not priming at all. I checked all fuses...
Finally got around to pulling the motor out of my 2001 cobra.
Dropped it and pulled the pan and saw this.
Obviously, that was the culprit for the oil pressure issues I was having at idle. I popped off valve covers and and timing chain cover.
The drivers side stationary tensioner was...
Ok finally getting around to pulling the motor out of the Cobra to figure out what is causing my low oil pressure at start-up and idle, only 7 psi at warm idle(operating temp) 40 psi at 1800 rpm.
I am guessing it is main bearings, motor has 22k miles on it since full forged balanced...
$200
Ford Racing Shorty Headers Stainless steal used, fit 96-01 Cobras, will bolt up to stock exhaust.
Located in Bolivar TN. Can deliever to Jackson, Martin or within 75 miles of Bolivar TN.
!!!Does not come with hardware or gaskets, Just the headers. !!!
text 7x3c1-6x5x9-1x4x0x2
$325.00
Bassani 46933 used . Good shape just a little surface rust. Went with long tubes so this is left over.
Located in Bolivar TN. Can deliver to Jackson, Martin or within 75 miles of Bolivar TN.
I prefer not to ship but if I need to we can work something out on price.
thanks.
Will...
Here is the situation, a while back I was driving to work and noticed the Oil pressure hit zero while sitting at a light. Thought maybe it was bad sending unit, but by the time the light turned green the motor started making noise...similar to dry start up after oil change. I immediately...
I was wondering does anyone know of a good Machine shop in the west Tennessee area. Got a 4-valve motor with a rod knock want to get it rebuilt to put in a ranger. Motor has only 20k miles on it since full forged rebuild. Heads where cleaned up and checked at the time of rebuild. Just...
The Car
2001 Mustang Cobra
5.1L BluePrinted All Forged 12:1 compression
Port Polish heads
Stage II camshafts
The Issue
The other day I was driving home from work. Everything running great get on the off ramp and then hit a stop light. Noticed a slight knocking coming from...
Was wondering if the 17x8" 94-95 Cobra wheels will fit my 2001 Cobra?
If they do what is the widest 26-27" tall slick I can put on that rim?
(I did search nothing came UP )
Thanks
JayRab
I currently have 18x10.5" rims in the back and I am only running 285 Nitto 555. I would like to go wider. Do you guys know the Widest I can go in the Back. 315 maybe or is 285 the widest I can go.
Thanks
Jason
I have a the following I am looking to get rid of:
Price Fitment
$150 1996-2002 Mustang 4v Ford Racing Stainless Shorty Headers
$350 94-04 GT & 99-01 Cobra Manual Bassani Catted X-pipe
$125 96-01 Cobra & 01 Bullitt K&N FIPK Intake it
Located in...
Ok here is all info on block cams and everything. Installed in a 2001 SVT Cobra.
BLOCK
Balanced and Blueprinted 5.1L Stroker
3.750in Stroke, 6.000 Rod
11 to 1 Compression
All Forged
HEADS
01 Cobra Head shaved .010
5 angle valve job
Hand porting
New Spring and Retainers
CAMS...