In December, I purchased a 2.3 L Whipple supercharger for my 2003 SVT Cobra, from
Lethal Performance. I understand that the supercharger came to me direct from Whipple.
I am in need of some supercharger installation gaskets and I received no gaskets, in my
box that arrived.
Where does everyone...
In December, I purchased a 2.3 L Whipple supercharger for my 2003 SVT Cobra, from
Lethal Performance. I understand that the supercharger came to me direct from Whipple.
I am in need of some supercharger installation gaskets and I received no gaskets, in my
box that arrived.
Where does everyone...
In December, I purchased a 2.3 L Whipple supercharger for my 2003 SVT Cobra, from
Lethal Performance. I understand that the supercharger came to me direct from Whipple.
I am in need of some supercharger installation gaskets and I received no gaskets, in my
box that arrived.
Where does everyone...
After fourteen years, I am finally installing a 2.3 Whipple supercharger.
Can anyone help me find a Whipple belt guide.
I currently have an Eaton with a 2.93 upper and a 4 pound lower, 3.2 alt pulley
and all the Billetflow pulleys offered. Now using a K080797 belt.
The Whipple will have a 3.50...
Has anyone had any problems with Nitto Nt555 G2 tires on their 03/04 Cobra.
I bought four new ones and my Ford dealer says the are all defective.
At 70 mph on the highway, there is vibration and road noise.
I'm told the tires are not perfectly round on the outside edges.
Help please! Ken
My Cobra is very low mileage and in very good shape. I was driving it yesterday and noticed that it was not starting like usual.
Almost seemed like it needed a tune up. I went out early last night and then parked it after a while of driving. When I started
the Cobra up again, it bucked and...
I have a 2003 Cobra with SCT XCAL 2 tune, 293 upper, 4 lb. lower,
air filter, SCT BA 2400 MAF, ported T/B, ported plenum, Magnaflow
mufflers in stock pipes, KB B-A-P and TR6 spark plugs.
I got a new tune with the monitors turned on.
Right now, I have my EGR and CATALYST monitors showing a...
I have a 2003 Cobra with SCT XCAL 2 tune, 293 upper, 4 lb. lower,
air filter, SCT BA 2400 MAF, ported T/B, ported plenum, Magnaflow
mufflers in stock pipes, KB B-A-P and TR6 spark plugs.
I got a new tune with the monitors turned on.
Right now, I have my EGR and CATALYST monitors showing a...
I have a low mileage, very good condition, Magnaflow catback
with slip in baffles for sale. No dents or scrapes on catback.
It is for an '03/'04 Cobra with IRS rear end. I installed a stock
catback with Magnaflow mufflers welded in. I am selling for $350.00
in Peabody, Ma. and is pick up...
What does everyone do for 03-04 Cobra oil changes?
I have Rhino Ramps and the nose hits the ramp and
pushes them. Don't want to jack up the frame anymore.
Are there any ramps that the Cobra can use?
I have done lousy ET's with my Cobra so far because the PPRV
hesitated so badly in between gears. It seemed like it slowed
me a lot. I usually rev the car to 2,500 rpm and feather the
clutch out on launch and then speed-shift each gear to about
6,400 rpm. This only gets me a 1.9 sixty foot...
I found this 2003 Cobra in the Want Advertiser for 2/27-3/5. Car is on
top of page 245. This is not my car, and I don't know the owner.
The car is a 2003 SVT Cobra Convertable and I'll write the ad as it
is written in the Want Advertiser.
2003 Ford Mustang Cobra. Convert. 4.6L V8...
I have an air compresser for sale. It is mint, hardly used.
Craftsman twin piston, 6.5 HP, 33 gallon tank, lays down,
not a stand up unit. It is 240 volt and uses 220 only.
It does not use 110.My wife won't let me hook up 220
to the garage as the 100 amp voltage panel is already
maxed out.I...
Does anyone have the video of a dog skating on a skateboard?
I think he was a Bulldog or one like that. It was really cool to see.
If you have it could you post a video link? Ken
My newest combo, 2.93/ 4 # lower and supporting mods worked
out very well. Dana installed my heat exchanger, I/C tank, 4 #
lower pulley, new belt, 2.93 and a 3.2 alt. pulley
Pete installed my BAP, another shorter belt, SCT maf, a I/C switch
and did a great tune.
My best numbers were 463.18...
I need a brand, number and length of a belt to fit my new combo.
2.93 upper pulley, 4 # lower pulley, new style snub idler with
1-92mm idler and 3-100 mm idlers and using stock alternator
pulley. Have this combo? thanks, Ken
I am ready to buy a Kenne Bell BAP 40 amp unit, but do
I need a wiring upgrade for it or not? What are you guys
doing with yours ? I need a BAP as I'm leaning out after
6,200 rpm's. Ken
I was up in the New Gloucester, Lewiston, Auburn, Maine
area on Sunday and about 5:30 pm, I passed an '03/'04
red or dark red Cobra as I was in my silver Cobra. Was it
anyone here on SVTP? Ken