I am in need of a drivers side front fender for my 03 Cobra. If you have one in good condition and are willing to ship please let me know. I guess it really doesn't matter but my car is a Red Fire Vert.
Question, are these available through Ford?
Looking for some jacking pads for the frame rails that will fit the 2014 GT cars. I have a set of round puck style that are too big for the slots in the lower plastic that runs from the front wheel well to the rear. They will go in the rear slot but not in any of the other ones.
I know where...
it felt like in the old days when a throttle cable broke. The car would idle but would not rev when I pressed the gas. It will in gear idle along as long as you are on flat ground but that is all it will do. When it first starts up I can rev it one time and that is it.
I have a cheep code...
Put 5 gallons of water/antifreeze in my 2012 with a few gallons of C85 still in the tank. Started the car and it didn't run to well. I can't imagine why, guess they are not meant to run on that combo.
Pumped the gas out and replaced with VP C85 and drove the car 60 plus miles home.
What if any...
I have a 2012 Mustang and am looking for a set of 15x10 wheels with single beadlocks. Looking for something in black, polished and black, and light weight.
I have a 55 gal drum of pump E85 that was pumped from the pump in South Fl apx 2.5 years ago. Stored in a VP drum on a pallet inside the entire time. It tested dead on 85% today.
Is there anyway for it to loose octane without changing the percent of ethanol?
Can it still be good for that long...
I am going to put a set of front runners on my street/strip car and am wondering what size tire others are running on the street? I have a dedicated strip set up and like the way the car looks with the skinnies but don't want to run that high priced race tire on the street.
A little help please.
Looking for information. Have any of you installed coil over shocks on a coyote swapped car? If so which ones did you use and what k member, what spindles, and does is rub?
Thanks.
I have to replace a leaking intake gasket on an engine with a set of GT40X heads. When I pulled the intake off I can see right away why it was leaking. The gasket is not matched for the head or the intake. Can anyone tell me what the correct part number is for the gasket for that head?
The car...
Should I be concerned about replacing the heater core in my 1990 Fox? Just a little worried about breaking the plastic because of its age. Is this a potential problem?
What say you?
Some people like the sound of a push rod motor, some like the look of the original seats, some like the original dash, some want the stock hood and some would not mod it at all.
If you were going to build a fox how far would you go with the mods?
Swapping the engine, seats...
This Dart was just finished by a builder in Central Florida. The car was a 2016 SEMA car with a blown 493. With its SEMA obligations behind it they brought it back to Florida to have a new Hellcat engine with a KB blower installed along with a upgraded suspension.
Hopefully you can see the...
Thinking I need a clutch in the Mach-Notch because it is releasing right at the bottom and all the adjustment is out. (1988 Fox with all Mach 1 components) It has the Mach 5 speed and engine and I assume that it makes stock power, however the engine is built for boost should I or someone else...
Wasn't sure where to put this so I will start here. bought a set of new Weld single beadlock wheels and am looking for the torque sequence and the install sequence. Weld's site gives the torque at 18ft but i can't find the install sequence. Can someone help a brother out?
Anyone have experience launching with 800hp on the street? Car cuts 1.3s at the track on a Pro tire, put a slick on and left the shocks set from the track at 3/7 with no luck. Using Ford Racing 1" lowering springs with stock bump stops. Have all the goodies in back just wondering if a different...
I would like to hear from you guys that HAVE return style fuel systems that don't smell. My 2012 has one and it smells too strong for me. What did you use??