Got my t56 magnum in and just double checking everything before start-up. Noticed that the throwout bearing is against the pressure plate. Normally there is some space between the TOB and the pressure plate fingers. It is so tight that I cannot turn the TOB. It is tight even with the clutch...
Replaced my stock K member with a PA Racing tubular K. Put the motor in and tightened up the motor mounts and the motor can be rocked on the motor mounts fairly easily. I can push on the bottom of the bellhousing with one hand and move the back of the motor up or down 2-3 inches. Is that normal...
Have an OTC-6498 cam tool for Ford Modular engine.
Kit includes: Camshaft positioning tool, camshaft holding tool, crankshaft positioning tool and secondary chain tensioner tool.
Used once. PM me for pictures.
Looking for $75.
Anyone looking for a clean, used T45?
Has 10k on it since rebuild. Shift fine through all gears. No noise. Ran Royal Purple in it since rebuild. Comes with Tri-ax shifter. PM me for pics.
Looking for $500.
I have a few parts laying around that I am looking to get rid of.
T45, rebuilt with 10k on it. Came out of the car with 75k on the car. No issues while in the car, replaced with magnum T56. Comes with shift fork and Tri-ax shifter. PM for pics. Looking for $500 or bro. Will deliver within 100...
Is anyone using one of these? I am looking at buying one, but would like to hear a review or two before ripping out the stock windage and replacing it with one of these.
Thanks!
I am trying to figure out if I want to sell my Procharger to upgrade to a D1SC
I am the second owner, the first owner put 1231 miles on it. I have put less than 1000 miles on it.
Blower was checked and all seals were replaced by Superchargerrebuilds.com. It comes with a 3.4 pulley...
I have just about reached my limit with this belt issue...:fm:
My setup:
8 rib pulley setup. Procharger P1SC with new 3.4 pulley. Alternator, A/C, Power steering, water pump, idler and tensioner are all stock pulley diameters and new. Crank pulley is brand new, Navigator (7"). I am running...
Had to replace my input shaft seal (threw a belt...different problem:fm:). When I opened my P1SC case I found the inside was coated with black oil. I just changed the oil less than a month ago and barely have 200 miles on it. When everyone else changes their oil, is it black? The oil color is...
I have a 10% over drive Innovators West crankshaft harmonic balancer. I need to go back to a stock diameter. Anyone have a stock diameter IW balancer that they would trade straight up?
I saw 13+ psi on a stock pulley for a procharger P1SC with this balancer. The balancer has less than 200...
Ford Motorsports 39# injectors. Less than 1000 miles on them. All in great shape. Went to 60# injectors. $160 for all eight with shipping.
PM me for pics.
Thanks
I recently completed my blower install and am ready to take it to the dyno for final tuning, but I can't get the car to go anywhere. :shrug: It starts out fine, but at soon as it start to move the car bogs down and dies. It will not go over 10 mph or over 1500-2000 rpms (in forward or reverse)...
I am hooking up my KB boost-a-pump and the instructions tell me to install the vacuum/pressure switch in the engine bay. I would rather not make another tee into the vacuum lines and run another cable from the trunk to the engine bay. I heard you can just connect the red/black lines together and...
I need to get a set of subframe connectors welded on my 2000 GT. Can anyone provide a recommendation for a reputable suspension shop in Southern Maine/Southeast NH?
Thanks
Has anyone ever put a slot style (05 or newer) MAF in a 99-04 Lightning housing? Is there a way to open the hole in the housing to accept a slot style MAF? Or am I totally off my rocker on this one?
I was going to use a 90mm MAF from a Lightning that I already had, but the tuner says I need a...
Used Procharger 2-core intercooler. Came with Procharger kit for 99-01 Cobra, but will fit others. 3" inlet and outlet. According to ATI this intercooler supports up to 550 HP max. 18" x 12.5" x 3" No issues, went to a bigger Treadstone. $110 shipped.
Stock Cobra MAF - $30 shipped...
Anyone ever siphon the gas out of their tank? I need to drop my tank and its 3/4 full. I live in Maine, so can't drive it until it is empty. I bought a siphon hand pump, which worked for the first gallon, but it seems like it gets stuck going any deeping into the tank. Is there something that...
Hey guys,
I am in the middle of my procharger install on my '99 motor and ran into an issue with the upper radiator hose. I did not get the supplied radiator hose and need one. Does anyone have the brand and part numebr for the upper radiator hose? I would rather not buy the hose from...
I have a few parts for sale. Prices include shipping.
BBK Cold Air Intake #17130 - Fits 1999/2001 Cobra, includes instructions and MAF - some scratches - $120 - SOLD
30# Ford injectors - less than 1500 miles - $100 - SOLD
Ford coolant crossover tube - in good shape - $30 - SOLD...
Sounds like my IAC valve has an air leak. My car is idling high (around 1400 rpms) and irratic. I already checked for vacuum leaks and did not find any, but did find the IAC sounded like there was air leaking out or in. There is a black plastic cap on the IAC valve and the air sound is coming...