This is a supercharged 99 mustang GT with a 4V cobra swap done to it. Tuning was done by Lidio at Alternative Auto. Motor has about 9,000 miles, rear axle has 7,000 miles, T-56 transmission roughly 35,000 miles, and body 86,000 miles. Originally Oklahoma car, no rust at all, never drove in snow...
I have a posi ported Eaton for sale, #147. It has roughly 10,000 miles on it. I bought it about 10 years ago with plans to install on my mustang but it never happened and it is time to get it off the shelf. Also comes with new gasket. Asking $800 OBO.
What do you guys think an excellent condition Posi Ported blower would go for? I have one that has just been sitting wrapped up for over a year which I unfortunately wont be able to get around to installing it for at least another year. I haven't seen one sell on here since January.
For sale is a stock lower pulley. Everything spins fine on it and there is nothing wrong. Worked great still when it was removed from my car. $100 shipped.
[/URL][/IMG]
[/URL][/IMG]
I purchased this last year with the intent of swapping it out with my stock eaton. I will not be doing that now so here it is up for sale. The case has been sand blasted and is ready to be painted or polished (all openings were covered with duct tape along with the bearings) and has been...
like the title says, 99 mustang GT with a cobra swap done to it. i have done everything myself for this car except the tuning which was done by Lidio at alternative auto. motor has about 9,000 miles, rear axle has 7,000 miles, t-56 transmission roughly 35,000 miles, and body 86,000 miles...
does anyone know where I would be able to purchase the bolts that hold the rotor assembly to the supercharger case for the stock eaton? also what is the torque spec for these bolts?
For sale is a rebuilt 4.6L DOHC Lincoln Mark VIII. Parts that are new in the engine are as follows:
Main Bolts
Main Bearings
Rod Bolts
Rod Bearings
Piston Rings
Oil pan gasket
Head gaskets
Head Bolts
Intake Gaskets
Valve Seals
Valves have been ground and lapped into the seats and the...
For sale is a rebuilt 4.6L DOHC Lincoln Mark VIII. Parts that are new in the engine are as follows:
Main Bolts
Main Bearings
Rod Bolts
Rod Bearings
Piston Rings
Oil pan gasket
Head gaskets
Head Bolts
Intake Gaskets
Valve Seals
Valves have been ground and lapped into the seats and the heads had...
I have a Fuel Safe tank that is complete with the bladder and a fuel pump currently set up for return fuel. I will have pics up later but here is a link to the tank. These sell for $2,893 new I am asking $1,000.
Complete Late Model Mustang Cell, SA110A - Complete Fuel Cells - Late Mustang -...
I have a set of front Strange Engineering externally adjustable (10 way rebound) struts for sale. asking $135 shipped for the pair. I will have pics upon request.
I will be rebuilding my T-56 this winter (hopefully not sooner) right now sometimes at idle i have to double clutch it to get it in first and when going down the track something just doesnt feel "the same" which gives me the feeling its on its way out. It is a stock T-56 and i drive the crap out...
doing a manual steering and brake conversion so i have a few parts for sale:
Power steering rack with inner and outer tie rods. (outer tie rod boot is ripped) - $90 shipped
Hydrobooster with master cylinder - SOLD
steering shaft - $55 shipped
power steering pump - $35 shipped
power steering...
doing a manual steering and brake conversion so i have a few parts for sale:
Power steering rack with inner tie rods(2000 GT) - $90 shipped
Hydrobooster with master cylinder - SOLD
steering shaft - $55 shipped
power steering pump - $35 shipped
power steering cooler hard line - SOLD
03 04 cobra...
anyone know if there is a write up anywhere on how to disassemble the lower pulley? my inner belt broke and some of the belt material wrapped up inside the lower crank pulley. i was able to get all the pieces i could see but now when i spin it freely i can feel a little more than normal...
have an 03/04 cobra factory OEM power steering reservoir bracket for sale. Asking $130 shipped. The bolts / studs that the reservoir bracket mounts to the pulley bridge are included as well even though they arent pictured.
went to Milan on saturday and was going to race in the Holbrook shootout wild street series. unfortunately, my day was cut short because i broke the inner belt during the 2nd qualifying round and didnt have a spare with me but during one of the test and tune sessions I ran a 10.94 @ 125.97 mph...
went to Milan on saturday and was going to race in the Holbrook shootout wild street series. unfortunately, my day was cut short because i broke the inner belt during the 2nd qualifying round and didnt have a spare with me but during one of the test and tune sessions I ran a 10.94 @ 125.97 mph...
My car is becoming more of strictly a track car. hardly drive it on the street anymore. This summer I am possibly doing a manual steering/manual brake swap. ac has been deleted for a while now so the water pump would be the only thing driven off the inner belt so I am thinking of doing an...