Who's using them, and who did you have do them?
Debating on making the switch. It only makes sense to go that route and free up the flow a bit. You all notice any power increase? Any torque decrease? Thank you guys.
Side note I just noticed I have been a member for 4 years wow time flys by.
I have a SRA out of an 01 Bullit that has quite a few things done. I am looking to go back to a nice IRS with low miles.
Edit: 19k miles on the car, 1500 on the whole SRA
-Moser 33 Spline Axles
-Moser Spool
-C-Clip Elim.
-Welded Tubes
-UPR UCA
-UPR LCA
-UPR Spherical Bushings
-UPR...
I just currently got stationed at Fort Eustis, for the time being. Not sure as to how long I will be here but, what I need to know is:
What good shops to work on my 03 Cobra are in the area?
Who is the best tuner in the area?
Is there a community forum for the Tidewater/Newport...
Does anyone sell aftermarket stiffer mounts? Does anyone have some in their car already? If so what kind of power are you making and how does it feel? More vibration? I think it would greatly improve shifts right? Thanks! :rockon:
I have had my car for sale for little while it appears it isn't going anywhere. So I am debating on throwing an auto in the car and some 3.27's or maybe lower in the rear. I already have a .020 over motor and built 8.8.
Now I already have a T76BB kit on the car makes 660 @ 18lbs (low timing...
I have 15x10 and 15x4 TRUE Weld Prostars.
Tires:
Hoosier Quick Time Pro's: 27x11.5x15
Hoosier Fronts: 160/55/15's (I believe I can't remember exactly)
I would like to trade for a nice street wheel/tire. I don't have anything to put on the car so no I won't sell out right.
I also have...
FS/FT 2003 Hellion Cobra with only 19k miles, over $30k invested
I am the third owner, I bought the car with 12,xxx back in 2006. The Hellion T-76BB Kit went on at 15,xxx miles. Car on stock motor with 18lbs made 717.7/672. The car is very capable of 1,xxx with more boost and the addition of...
I need this to happen ASAP my car has been down way to long and this is a last minute change to the build.
My T-56 details:
18K miles
BRAND NEW Southbend Stage 5 clutch
Stock flywheel
BRAND NEW Liberty 26 Spline Input
BRAND NEW Lethal Perf. Aluminum TOB Sleeve
BRAND NEW HD TOB
BRAND NEW New...
This isn't getting much attention in the Turbo Cobra Section so I am opening it up a bit.
What RPM are you leaving from?
Are you using a two step?
How much boost are you building at the line?
Are you spraying?
Also the car is a Hellion T76 car.
My setup:
01 Bullit 8.8
Moser...
What RPM are you leaving from?
Are you using a two step?
How much boost are you building at the line?
Are you spraying?
Also the car is a Hellion T76 car.
My setup:
01 Bullit 8.8
Moser 33 Spline Axles
Moser Spool
C-Clip Elim.
Welded tubes
UPR Chrome Moly Adj. Race Lowers
UPR Chrome Moly...
Maybe this has been addressed already and I am just unable to locate the thread but:
I have an 8.8 (still has the cobra brakes on the back) in my 03 and want to do slicks an skinnies. If I'm not mistaken its 15x4 w/ .5" spacer and 1.75in BS, and 15x10 w/ 6.5in BS. If I got with a smaller BS...
So I got to thinking where are all the other guys that can relate to what I have:
1. Username - Location - Kit (i.e. Hellion, HPP, Custom..) - Power - Tranny
I'll start.
1. Dover - Columbus, Ohio - Hellion T76BB - 717.2rwhp - 6SPD
2. Janstang - Rapid City, SD- Custom T88- old setup-...
Columbus Racing members have organized Columbus Cars and Coffee Meets. This is their second year at it and it continues to grow. So feel free to swing on down/up and hang out and meet some car guys/girls likes yourselves.
Website with detailed information can be found here:
Home
Feel...
Finally about done with the car and doing final touches. Question for all you SRA guys.
Currently I have an 01 Bullit 8.8 on the car. My plans are:
Moser 31
Detroit Locker
UPR Upper/Lower CA's
Girdle
3.55's
Car is a 6 Speed, made 717 prior with an IRS an stock clutch!, just switched...
My build is almost complete (Pictures to come). What I did:
.020 4V
Mahle Pistons
Manley Rods
Cobra Crank
ARP Main Studs
ARP Head Studs
ARP Rod Bolts
Feldpro Head Gaskets
Heaving the heads looked over still debating if we are going to CNC them and what not.
Still has the BBT76 Kit...
This is a complete feeler, I really honestly don't know if I want to sell it. I have went to the darkside, I bought an 08 Busa and I just can't have fun in the car anymore. :shrug: Well to the car. I am the second owner, I bought the car with 12,xxx back in 2006. The Hellion T-76BB Kit went on...
Who is selling a kit to go blow through with the Hellion T76 kit. Or who knows the best route to do it?
I have a Sullivan upper an lower instead of the Mach/01 Cobra setup. Thanks guys.
Billetflow 03/04 Cobra Pulleys (Buy them both and I have a brand new Belt to work with them)
- 2.930 (Silver) - Used - $50
- 3.100 (Red) - New - $75
Add shipping and 3% for paypal.
Link to Billetflow:
http://www.billetflow.com/supercharger_pulleys.htm
What is the best route to go with heads on our cars?
I melted Cylinder 1 piston all over the Passenger Head, also the valves appear bent in the cylinder. So I might as well replace it all. I'm going to keep the stock cams cause I have read that people arent seeing any real big difference...