Hey guys I have a Fox mustang (82 fairmont) with 2001 mustang brakes and spindles.... i want to get a set of front skinnies for it and I needed some guidance about what size/backspacing will work from the experience on this board.
I have the following options in a 15" wheel....
Billet...
guys i have this belt on my 03 cobra, it squeaks like hell for the first 10 minutes after startup.
any auggestions for a different brand or length?
i dont know the exact pulleys on it but its making 21lbs of boost.
thanks
http://www.jegs.com/i/Gates/465/K080780/10002/-1
guys
Imy 2004 lightning is stock, I am getting a bog when I am accelerating lightly at the 2-3 shift. also at 70mph cruise if I'm going slightly uphill I get a bog.
This bog feels like the car is about to stall and then comes back.
Any thoughts ? I'm thinking coil on plug, plugs ? Torque...
Is the 03-04 cobra headlight panel a different design than the regular mustang ?
https://www.ebay.com/itm/182740942744
2003 - 2004 MUSTANG SVT COBRA 4.6 HEADLIGHT PANEL BLACK SKU# DD29
Does anyone know what part number this is ? Is it for t56? I'm assuming it a hydraulic tbrowout conversion/master cylinder kit. Just missing the throwout ? What do you guys think ? Thanks
guys,
my rear end is leaking and I want to top it off. I can't get any access to the top fill plug, it's ridiculously tight. any tips to be able to refill this? ???
i currently have a McLeod twin disc clutch in my Car that is gone. Is there anyway I can tell if it's 26 spline or 10 spline without dropping the trans ?
is a clutch install on jackstands doable on these terminators ? Would I need a tranny jack ? Anything specific with these cars that is a pain? I have full length headers.
Thanks
Guys my lower idler pulley is bad. It threw a belt and WOT 4th at the track.
I bought a 100mm idler from UPR but it doesn't look like it'll fit. (Bearing is a bit wider) The existing chrome bracket says METCO.
Will the idler pulley below work for me ...
See pics In post below. I want to identify the type of engine and heads on this car ?
Is it an aluminum 4.6? Do they look like stock pistons?
https://www.svtperformance.com/forums/threads/what-engine-head-is-this.1131085/
hey guys, I need your help with this:
can you tell me what engine/head combo this is?
From pictures online I think it's a 4.6 aluminator crate motor? But I am not sure. what heads are they?
Thanks
What is the full level of one of these aftermarket moroso engine coolant reservoirs?
There is no fill line on them ? Anybody have a general guide for how full they should be ...
2003 Cobra
4.6 Aluminator Crate Motor
VMP TVS Blower 21lbs of boost on E85
Magnafuel 750 Pump w/ ½ lines
In 3rd & 4th gear at WOT, I was blowing coolant out of the engine coolant reservoir. It is a moroso steel tank with a ford 16lb OEM cap. I replaced the cap as I read on the forum that they...
hey guys I'd like to rent a U-Haul auto transport trailer to pull a car with my lightning.
Has anyone used one of these U-Haul auto transport trailers with their lightning ?
I'm assuming you do not want to drop hitch because these trucks are already much lower than a regular F150.
Any...
hey guys I'm running E85 with an aeromotive race fuel pump. The pump has a controller with 1/2 lines. It runs great but after about an hour of driving on the street and making a WOT pull, The car will stumble a bit at idle and once in a while stall . it only seems to do this after a long 1hr...
Hey guys I just purchased an 03' cobra that has all of the AC components removed. The car was a race car so everything under the hood related to AC has been scrapped.
The car is a running car right now but I obviously would like to have AC.
Is there a list or any picture/diagrams of all the...