Search results

  1. bmxr152

    WTB: 10th Anniversary Terminator

    I have one for sale in reno with 38k miles
  2. bmxr152

    Trunk vs under hood ice tanks

    Honestly that's what I was thinking too. Now with megasquirt it makes it a lot easier to go that way as well.
  3. bmxr152

    Trunk vs under hood ice tanks

    So i have been battling back and forth with the debate of a bigger under hood reservoir or a different trunk mount ice tank. Currently i have a 4 gallon trunk mount tank with a failing pump and a tank lid that just keeps leaking. Im either debating on getting a new pnr tank with a varimax pump...
  4. bmxr152

    Megasquirt idle issues

    Okay, i need to figure out what the default numbers were as well. Setup as far as motor? Im running 9.8cr built bottom end with comp stage 3 cams, degreed to comps specs. Currently running stock blower with 2.76 and stock size lower, bbk long tubes, JLT high boost intake, 80lb ford racing...
  5. bmxr152

    Megasquirt idle issues

    Air fuel table is setup correctly. I still need to link each wideband with its bank. As of right now im using 1 wideband to control all injectors even though both are hooked up. During install i didn't have each one marked so i will need to remove and test each bank to see which is which. Yeah...
  6. bmxr152

    Megasquirt idle issues

    Okay good to know. Ive got it to cold start good and idles fairly well, but any throttle input and then it wants to die and surges like crazy. Hot starts are a pain and i always have to input throttle. When your talking about main ve table, are you talking about the fuel table or ignition table...
  7. bmxr152

    Megasquirt idle issues

    Yeah having fun for sure. Its been over 106* out here in west texas lately, so ive been taking baby steps and trying not to be out in the heat too much. I probly need to bring the spark down then in the idle cells. Its around 20* right now.
  8. bmxr152

    Megasquirt idle issues

    So i got my megasquirt ms3pro installed and setup all the basics with dual widebands. I calibrated throttle, adjusted timing so it was dead on as well. I also made sure to calibrate coolant temp. So the issue i'm having is i get crazy idle surge once i tap the throttle. also when its warm and...
  9. bmxr152

    Megasquirt MS3 pro users

    So looking at the instruction fort the rear auxiliary connector it only has one input for wideband o2 sensor in the G location of the connector. Running the dual spartans, do you wire into the factory ecu connector then? Also has anyone used the inter cooler pump output to control the inter...
  10. bmxr152

    Megasquirt MS3 pro users

    So will the megasquirt work with the factory maf properly?
  11. bmxr152

    Megasquirt MS3 pro users

    So what is the issue with the reverse lockout? Does everyone have this issue? Anyone have pictures of their intake setup with no maf?
  12. bmxr152

    WTB KENNE BELL 2.2 but open to other blowers

    Hell yeah, how much did you get it for?
  13. bmxr152

    WTB KENNE BELL 2.2 but open to other blowers

    I have a kenne bell 2.4 that has been sitting at the shop for a while. Nothing wrong with it except for needing a good polish, a new bypass actuator and throttle cable bracket.
  14. bmxr152

    Megasquirt MS3 pro users

    Yeah i get the house thing! Im currently in the same boat. So what kind of intake setup are you running with no maf now? I was thing out fabing up a fender well style with my existing short ram.
  15. bmxr152

    Megasquirt MS3 pro users

    So i have mine ordered with dual spartan widebands. Hopefully it wont be to hard to get everything running well. The plug and harness to wire in the widebands to comes with the megasquirt correct? Im hoping i can get all up and running in a weekend at the shop since i need to be able to run flex...
  16. bmxr152

    Updated engine noise

    Did you ever figure this out. My 03 cobra has a similar noise only in those rpm ranges
  17. bmxr152

    Alternator preferences

    I have the newer style 185amp J2 fab and all i can say is its night and day difference from the ebay made in USA specials and ford remans. I hold a steady 14.2 at idle and see no less than 13.4 any other time, loaded or at WOT. That is seeing voltage with my SCT. I highly recommend the J2 fab.
  18. bmxr152

    Megasquirt MS3 pro users

    What knock sensor are you running and where are you locating it on the block?
  19. bmxr152

    Megasquirt MS3 pro users

    Okay that makes sense. Do you run no lift to shift or 2 step? Was it hard to get it to startup on e85? I'm worried the startup is going to be the hardest to get it setup for e85 and what not
  20. bmxr152

    Megasquirt MS3 pro users

    double post
  21. bmxr152

    Megasquirt MS3 pro users

    So, i was thinking about getting the dual spartan widebands for the setup so i can auto tune. For wheel speed sensors you cannot use the factory ones? I am also going to be doing flex fuel as i am on e85 currently. I was thinking about running it on the return side closest to the tank for the...
  22. bmxr152

    Megasquirt MS3 pro users

    So who is doing the work on the ECM, diyautotune? Im really pushing towards the megasquirt as i dont see any really affordable options that allow full control at this point. I heard HP tuners was junk for our platforms as well. So do you run fuel pressure inputs or any other inputs to megsquirt?
  23. bmxr152

    Megasquirt MS3 pro users

    So i have been having issues with my SCT xcal 4 cutting out the gauges. Basically when i do a pull the gauges dies and then the tuner says disconnected when I'm data logging. I was thinking about going the megasquirt PNP route but wanted to hear some input from some users. Ive tuned a few cars...
  24. bmxr152

    Installing ATS Brembos on the Cobra.

    Im going to be using the S&S engineering kit, is that the same as what your talking about?
  25. bmxr152

    Installing ATS Brembos on the Cobra.

    So does anyone know of pads that fit without grinding down pad material? I'm trying to make the install easier for pad swaps after track days.

Top