Search results

I bought these from another forum for my Supra build but they are WAY too big to fit my wheels. Everything is in great shape and unused, only thing that is missing is the banjo bolt and square adapter for on of the calipers which was not there when I got them. The pads are already in the...

Baer 5 lug conversion. They modify a stock fox spindle to accept a Cobra rotor and caliper. Fresh bearings and ARP extended studs in the front. Rear is a complete 8.8 with 3:73 gears. I also have a 93 cobra booster and master cylinder for this setup with a Maximum Motorsports prop valve delete...

B&G Intercooler kit B&G intercooler kit. Aluminium pipes with couplers and T bolt clamps. some slight bent fins but it is a used kit. 3" in and out. $150

ABACO DBX 85MM MAF with pigtail, unsure of miles but its in great shape. Had it on my fox for 100 miles before my rod bearings decided to not stay together. $200

South Bend DXD clutch for a 26 spline input shaft. Rated to hold 600ish ft/lbs and is BNIB, tape is not even cut yet. Only reason I am selling this is I need something to hold more power :rockon:. $300

Getting ride of my Wifes bike, its a 2007 Suzuki GSXR-600 with 10,079 miles. True mileage is around 8,000 miles as it was ridden for a season and a half geared -1/+2 without a healer which is now installed ( MPH is lower than true due to my on the fly math) and its only geared -1 in the front...

I wouldnt spends Easter Sunday any other way

I have decided to sell the bike to fund other things, I got this bike on trade for my Lightning with next to NO miles. It currently has 5043 miles on it as it sits in my garage and maybe 2000 miles with the gearing ( always had a calibrated speedo healer). The bike is in mint shape and is always...

Went and looked at a 86 Fox GT with a 351w swap and an auto (stock auto i beleive). Car is a non start ( fuel issues) but does crank over with no problem. A lot of the electrical has been hacked at but this car is a carb car so most of it is ignition related which is an easy fix. Body is...

OEM 01 tails: 50 shipped OEM upper grille with FORD emblem: 100 shipped: O SHIT handle with bolt caps: 30 shipped Unkown Billet grilles, need riveted in and the bottom one is a little tweeked: 75 shipped

01 OEM Fuel rail: 30 shipped OEM Intercooler Res. W/ bracket: 40 shipped Volant CAI w/ updated large elbow and new filter: 125 shipped 99-00 Lower intake: 80 shipped ProM 95mm MAF housing w/ MAF meter: 90 shipped OEM IC fluid pump with bracket and pigtail: 30 shipped...

Unknown Traction bars, has the shims and new grade8 bolts just need painted: 100 shipped (weight)

Friend of mine and myself started it as a little fun site. http://www.antizombiecrew.com/forums/index.php

2001 Lightning 59,xxx Miles (chassis) 480hp/551TQ @ 16PSI-Sunoco 94 pump gas ENGINE: JLP shortblock ( maybe 3k on motor) 01 Heads hand ported Crower Stage2 cams with supporting valvetrain( springs locks and retainers) Gasket matched lower intake Reichard Racing Blower Spacer Ported...

Unsure of brand it came with the truck, comes with a belt and the bolts to install. 100 shipped

Thanks go out to Cannon, DBL G @ DMR, Brian at Dynotune Motorsports, and my check card/lack of sleep.

-Used Borla muffler abd clamps that came on my truck. Was connected to stock mids and sounded fairly decent but i went full exhaust. $125 shipped OBO -Set of BBK shorty headers, again came off my truck from previous owner and ditched for a long tube setup. They are in ok shape except...

-I have a set of brand spanking new Belltech 2in. drop spindles. They are the newest version with the correct tie rod orientation and machined lower ball joint area for nut clearance. Some surface rust but this can be cleaned off. $275 shipped

150 shipped to your door, comes in the box but no instructions ( non needed really) Worked perfectly on my truck but i went with Sniper and dont need it. Guarenteed unlocked and if it doesnt work ill buy it back.

Seriously what is the deal here, i tried for hours to get me -8 line over the -8 fitting and no such luck. Do i have to do a ran dance and cup my right nut to get these things on or might i just need to get the sand out of my va jay jay. Is there something i am doing wrong or maybe some type of...

I got my intake back from my freinds machine shop to have somethings done along with the coolant X over mod. I gave them a breif description of what i wanted done and they got the idea. Got it back yesterday and they did a fantastic job but there is one problem, they tapped the holes 1/4 NPT...

I am putting together a little montage and would like to see what we can turn up and i am a complete and total perv. I have seen two of slcks videos ( especially the HD only one) and there were quite a few nice ones. Thanks guys.

Selling the LTs i was going to use but decided to go big single. They have everything but maybe like two bolts for the collector to cat and the gasket that connects the two. I also am including a Magnaflow Xpipe i have never installed. Asking 950 plus shipping. Please call...

Coolant X over mod, cleaning IC, Reichard blower spacer, Dynatech LTs, complete fuel system are all getting installed this month. Havent started the LTs yet but i already ran into a problem with the spacer. The guide pins are too big for the lower intake and IC assembly so the guides need...

Is it possible or will the stock BOSCH pump take a poop/ not keep up?