So, I live in Mississippi, and own a 2005 Yamaha YZ125. I was looking at a universal enduro lighting kit to try and make it street legal to putt around on. I know the 2-stroke engine is not built for this constant RPM, but I am just trying to see if it can be done.
Can anyone help me...
The other day I think I broke my big toe. It hurts very bad with any slight pressure on it, so I got some old crutches. What steps should I take for my big toe to heal back properly? Thanks for any help! :rockon:
EDIT: Guess I am headed to the doctor now...
I guess it is time to sell my one true love. :nonono:
Not accepting trades or parting out, thanks though!
Asking Price: $19.5k and it's yours!!!
Feel free to come check it out, ask for certain pictures, or just any general questions.
Will have more pictures next weekend!
Being a...
I know this has probably been discussed, and forgive me if it has. I was looking at some cheap 15x10" wheels, with a 6.00" backspacing. I know I might have to grind the tie rod some, but other than that, is there any problems of fitting these wheels on the IRS? Low profile IRS bolt needed...
I think I remember a while back reading you should not mix slicks and street tires. By this, I mean running street tires up front and some slicks out back. Is this correct, or does it not really matter? Thanks!
Went to just inspect the car today, and I took off my wheel to just look around. Forgive me for how dirty it is, plan on washing it tomorrow. Anyways, I noticed the inner side of the tire to be rubbing on something, and now the radial is showing. I got Bruce's bushing kit installed a while...
What do you guys have the shifter handle seated at? I have mine way up on that little shaft, as I believe it might give more leverage. Is it better like this, or should I seat it a the way down until the stopping point on the shaft? Thanks!
The other day I was playing around in the Cobra. I started in 2nd gear at about 50mph and just did a little hit. Right when I went, the car just like stopped pulling. It was still making the blower noise, but it was not like belt slip, or clutch slip, so what could it have been?! I do not...
I was planning on gettig my car dyno-tuned sometime, as I only have a canned tune right now, with an X-Cal 3. Just wandering shoud the price be for just a couple pulls to get the right timing/ a/f, etc. where it should be? Thanks!
I have just a basic upper / lower pulied Cobra, with a canned tune from Amazon on my XCal 3. Since I am not looking to get a dyno tune at the moment, I was wandering if it would be ok to mess with the a/f on my XCal 3 since I believe it is running a little rich. Under WOT, what would be a...
Mods for tranny/clutch are as follows: MGW shorts throw, Sped 3+ clutch, 26 spline input shaft, LDC freeplay mod, Spec Aluminum flywheel, Billetflow firewall adjuster, and MM clutch quadrant. I had adjusted the cable to where there is 1/16" gap between the pressure plate teeth and TOB. The...
I have a mail in tune from Amazon, which as I read about them, I learned they send pretty safe tunes. I was wondering with my tuner, if it would be safe to up the WOT A/F ratio a little bit, since I sense it running on the rich side. Will I notice any performance difference?
Today I tried a burnout with some new tires I bought. I did a pretty lengthy one, maybe 10 seconds long on the street. Anyways, when I drove off, smoke started coming in from under the dash and my car was filled up with burnt tire smoke. Are there any possible openings I can check to make...
My car has been having crazy wheel hop lately, to the point where I can not even do a burn out with out it hopping. I decided I was going to look for a solid axle, but was wandering the best strategy. I was wandering if I should A) straight up trade for a built 8.8" (if that is a good deal?)...
I just bought the Gates 80 1/8" belt, mods include: 2.93" upper, 4# lower, 4-piece Billetflow idlers, and 3.2" alt. pulley. I can not for the life of me get the belt on the top supercharger pulley. Is there any trick to it? I am about an inch off. Another thing, I read that people with the...
I just went out and got the 9/16" Grade 8 bolts and locking nut to replace the old 12mm ones. Is there a special way to break the torque on the original bolt / nut? It just seems I can not get any leverage on it. Also, should I purchase a washer for the new setup or will I be fine with just...
I have all 4 Billetflow idlers, 3.10" alt. pulley, 2.93" upper, and 4# lower pulley. I am currently running an 81" Gatorback belt, that has been on for about 17k miles and it has obvious scuffs and tears on it. In my opinion, it has symptoms of belt slip and I was wondering if I should get...
Well my battery died about 8 days ago, so I thought that was it. I went and got a Duralast red top from Autozone, still have warranty by the way, and it died today! So, I can only assume it is my alternator. I was planning on getting another OEM one, but can't seem to find any online. Does...