Search results

My car has been driving fine. 96 cobra daily driver only 74,000mi. I went to start it up wednesday morning and it won't start. It cranks but it seems slow. Plugs are getting spark and there is plenty of fuel in the cylinders. It hasn't thrown a code. I guess because the last time it drove, (2...

SOLD 1996-2004 UPR Chrome-Moly K-member kit. This kit includes 12" 350lb springs. It is 100% complete with everything UPR includes. I took it out of the box for inspection and started to bolt up the k-member to the car and then decided I didn't want to go through with it. The control arms are...

I tried searching for irs in our thread but didn't get anything. Has anyone done this/have pics? I'd like to know the locations where it would have to be drilled. Does our driveshaft work, brakes? How big of a pain was it? Was it worth it? any comments. I know the axles are slightly longer on...

delete please

Hey guys. I've got a 10 inch mtx thunderform subwoofer enclosure for sale. It's new in the box only opened it to check it out. This piece sells for $350 on Crutchfield http://www.crutchfield.com/App/Product/Item/Main.aspx?showAll=N&g=530&i=236FMC1T45&c=3&tp=113&avf=N Comes complete with...

I'm looking to get upr's front k-member kit with the coil over set up for the front. I'd also like to have the same adjustablilty and setup in the rear, however it doesn't look as though upr makes a rear kit. I know mmr and mm make kits but then I'd still be mixing and matching. So is it bad...

i've got my heater ground grounded to the block and the system ground grounded w/a battery ground on the frame. i've also tried grounding the heater ground to the firewall to no avail. it's an innovate lc-1 the controller works great except when i let of the throttle the voltage peaks and...

im getting some guages from a new local company and don't have any experience with them. wheres the best place/best way to place the sensor for the water temp guage? anyone hve any links to how to's on our cars or engine pics showing the sensor setup? thanks

i pressed my wheel studs into the axle on a press but unfornately some of them aren't in perfectly straight and the wheel won't quite fit on them. i installed the axles and i've used washers and a lug and torqued them down to 90 ft lbs but they still didn't straighten up enough. also tryed...

just changed the rear pads and now when i engage the parking brake with the rear off the ground the tires still spin. the cable still moves and compresses the spring when the cable is engaged but the axle still spins

i downshifted to 3rd at about 70mph and then when shifting after this my clutch felt as though it tightened up quit a bit on me. it also seemed to be stiffer when shifting into 2nd and 3rd. it feels almost as though the cable got stuck around something but it doesn't happen during ever shift...

BBK performance part #1555. new in box. 3-piece polished aluminum pulley kit fits 1996-March 2001 4.6L Mustang GT/Cobra -ford changed the water pump pulley midyear on the 2001's. $100 shipped Quoted from bbk's website "Made from aircraft quality aluminum alloy these BBK under drive front...

edit sry meant to put this over in the sale items

new chrome 8.8 rearend cover. will ship with new chrome rear end cover allen bolts. $35 shipped. obo thanks. from the inside

I just got the Ford Racing axle girdle M-4033-G1 and they recommend a bearing cap stud kit M-4034-A for it. Where do these studs go? and should I spend the extra $38.00?

ok i finished my header install a couple months ago and removed the stb to jack up the motor. when i replaced everything the stb was hitting the top of the intake. so i think the motor is higher on the passenger side. now whats the best way to go about this my plan was to remove the two...

they say on their site that they fit 79-98 mustangs but they also say for drum brakes. i'm looking to do a gear swap and my housing is slightly bent from hitting a curb, so said the alignment guy. so i figured $875 for a complete setup saves me install $ on the gears so why not. but i need to...

ok so I'm fairly new here and I've noticed on a few threads guys knocking sean hyland. now I haven't been around racing much, nor do a know too much about engine builders and such but I've picked up his books before and they seemed ok. Just wondering whats so bad about him. not saying you guys...

hey guys i just refinished my headlights the other day and just had to share the results. I was reading a thread earlier about using plasticx from meguires but when i went to advanceauto they were all out. I asked the guy if the had anything for plastic because I needed to defog my headlights...

brand new chrome 8.8 rear diff housing cover + a new gasket for $25 shipped. pm me ...also have bbk underdrive pullies for sale part#1555 fits 96-2000 mustang gt and cobra $110 shipped. pm me tommy

my bbk intake rubs on my strut tower brace. when i removed it i noticed a chunk messing from it. the intake fits snug under the stb and rubs on the side where it bolts to the shock tower. i have since removed a portion off the corner of the stb mount to help with clearance but when the motor...

need to recalibrate the speedometer for new gears. i figured i could do so with a tuner but the sct site says you can only recalibrate for a 99 up stang. wats with that? does that mean i need to spend $100 bucks on a recalibrater like the ford racing or dallas mustang one? that would suck

ok so i just put in headers and the passenger side is leaking so i went to buy a new gasket to put in. The dealer said they now make the gasket 2 peices for each side rather one (one gasket per 2 primaries). is this right?

ok so i saw an old thread where the majority said u/d pullies are worth it but i'm still not convinced. i have a set of bbk's tht i got a year ago but never bothered to install them. is it worth it any cooling issues, charging issues? how much power can i expect? should i use all the...

i took my 96 cobra to get dynoed and when the guy left off the gas after pushing it to red line it smoked quite a bit. he suggested running a thicker oil. what do u guys think. I am currently running 5w 30 mobil 1 full synthetic i've been doing so for a couple years now. I also orginally had...