Looking to do better at the drag strip with the 2013 GT500 this summer and wanted to get a set of drag wheels/tires to replace the factory 20s. I like the look of the Racestars but wanted to know if the 17x10.5 will fit without modifications to the sway bar and brakes? I know they make 18s but...
01yellercobra - If the voltage is right at the pumps with the way the BAP is wired and the only thing I’m doing different is removing the BAP from the system and the check engine light goes out and the voltage readings go to normal ranges for the fuel rail pressure sensor what else should I be...
BAP was installed 12 years ago and it was wired pre-FPDM without the hobbs switch and no dial is in the car to adjust. Is it suppose to have 17.35v going to the pumps at idle or is the BAP suppose to ramp up voltage as the car goes into boost?
Still struggling with code P0193 - I've replaced the Fuel Pump Driver Module and the same code comes up P0193 - when I turn the key on with engine off I get 5.1v at frps and I'm getting 17.35v at the fuel pump which seems wrong to me, I think the Boost-A-Pump is designed to ramp up voltage not...
Just a 2.4 upper, JLT CAI, and VMP Tune - 11.6 @ 127 is the best I have done with it. I find the car is hard to launch with 20" tires - If I come out at 3700 it bogs if I come out at 4000 it usually hooks for a split second and then the tires don't hold, needless to say its a challenge but its a...
No I havn’t, I will look for that on the scanner and see if I can monitor it. I ordered a new FPDM yesterday thinking it may be damaged from age or just from the boost a pump over working it for the last 12 years, I am skeptical that it is the problem as I am getting 17.35 at the pumps but maybe...
2003 Cobra - car shut off while driving the other day and after inspection found power at the pumps but no fuel pressure - order new Deatschwerks 340 lph pumps and a PPRV delete kit, after the pumps came in and the tank was dropped I found the fuel line was corroded and that was the problem but...
Maybe its just me but it sounds like it is getting chunkier the more I use the red key. Exhaust is stock other than the side pipe restrictor plates are out.
https://www.youtube.com/watch?v=OPorq0lacKk
https://www.youtube.com/watch?v=nLW4EUl9B3I
Just Installed Michelin Pilot Super Sports on Boss 302S wheels. Tires are noticeable stickier than the stock Pirelli's but not as grippe as the Toyo R888's I replaced.
I am looking to go to 18" AFS Cobra Replicas and I am wondering what brand and what size tire to go to. I want to go as wide as I can without rolling the fenders and I want a sticky street tire. I currently run P315/35R17 ET Street II's and they hook well but haven't lasted very long - my...
Looking to replace my Nitto 555R's with a more aggressive tire for street/strip. I like the look of the Mickey Thompson ET Street Radial II's but I'm not sure if they are a direct fit or if they will rub. The size I am looking at are 315/35/R17's and I currently have a 10.5" rim with the low...
Does anybody have a sound clip of Snakebite Series blower at idle? I am considering going this route as I don't have a ported blower yet and the cost is roughly the same as porting and doing a lower -without the worry of lower causing issues. I don't want it to sound like a procharger or gear...
Trying to decide on a whipple 2.3L with a 3.25" pulley or getting the eaton ported and going with a 2.93 upper / 4# lower combo. With either set up is a bap, 60# injectors, and a maf extender the only supporting mods necessary, also wondering the power range of each setup? Any recommendations...
Just got back from a day at the track and managed a best of 12.30 @ 116.79mph. It seems like the ET is low for that mph. My last round of mods were Steeda catback exhaust with weld in Super 44's (replaced stock catback with weld in Super 40's) and a 2.80 upper pulley & whipple tensioner...
I just gained 50rwhp/14rwtq by adding a Steeda Catback and a 2.80 upper with a whipple tensioner.
Previous Setup
2.93 upper
JLT Ram Air Intake
Stock Exhaust
Dyno Tuned
423rwhp/476rwtq
New Setup
2.80 upper
Whipple Tensioner
JLT Ram Air Intake
Steeda Catback
Dyno Tuned...
Just installed Steeda Catback and it is a bit too quiet. I am using the stock h-pipe and don't have plans to change it at this point. I was looking at Spintech Pro Street Mufflers and Flowmaster Super 44's as I want the deeper muscle car sound without the blat. I'm want to be able to hear the...
I am looking at putting a drag radial on my car but I don't want to have to roll the lip of the fender or install spacers. I am wondering if the Mickey Thompson ET Street Radial II in P315/35/R17 will fit without rubbing? Also looking at Nitto 555R's and wondering which tire would be best suited...
My buddy bought a 2010 Shelby GT500 and is going to be doing some mods before the good weather hits up here in Canada and I am also doing some mods. I'm wondering if I will stand a chance against him or if I am simply going to be out gunned.
My car is a 2003 Cobra with the following list of...