Search results

I am completely changing setups and have no use for the following parts anymore. 2003 Cobra driveshaft. Comes with original rear pinion flange (not shown), no yoke. Great condition. $115 shipped T56 clutch fork with FRPP TOB with 50 miles on the TOB. Looking for $50 shipped Driver...

I am completely changing setups and have no use for the following parts anymore. 2003 Cobra driveshaft. Comes with original rear pinion flange (not shown), no yoke. Great condition. $115 shipped T56 clutch fork with FRPP TOB with 50 miles on the TOB. Looking for $50 shipped Driver...

I am selling my turbo kit because I am going with an entirely different motor. The kit was complete, but I will be keeping the turbo, intercooler, and blow off valve. Please keep in mind that the bov is pictured but I will be keeping. The kit will most likely work for the 2003-2004 cobra...

I am completely changing setups and have no use for the following parts anymore. Up first is a McLeod T56 blow proof bell housing that has literally 50 miles on it. It is $409 + shipping from most retailers. I even have the instructions as well as all of the hardware. The bell is already pre...

I am completely chaning setups and this is the only reason I am getting rid of these parts. All work flawlessly! Up first is a McLeod blow proof bell housing that has literally 50 miles on it. It is $409 + shipping from most retailers. I even have the instructions as well as all of the...

I have a 97 Cobra Cluster. It is in good verified working condition. I have a fuel cell in the car and never have had the fuel level sensor hooked up so I assume it is why it reads full all the time. All the other gauges work as they are intended because they are hooked up. Looking for sold

All for 96-98 Cobra in great working coniditon. Parts do not include shipping. Driver side power steering reservoir/coil bracket $20 Coolant crossover with both coolant sensors$50 Alternator bracket sold

I have a brand new Dallas mustang extended range speedcal SPEED-CAL, 1994-2004, 5 SPEED, EXTENDED RANGE*::*Transmission Components*::*Drivetrain*::*Mustang Parts & Accessories Superstore - 1800Mustang It is 125$ after shipping from them. I am not using it because I am doing an engine swap...

I have a 97 cobra engine wiring harness which is complete. It did have a MSD DIS4 so the coil connections have been professionally soldered/heat shrunk. It works 100% verified ok! Looking for sold Next up, a lower engine harness Starter, oil pressure sending unit, etc off a 97 Cobra in good...

I have a complete engine bay fuel setup for a 4v. Includes: UPR Billet fuel rails Paxton adjustable fuel pressure regulator -10 feed, -8 return -8 feed lines post regulator to rails with all AN fittings. Looking for Sold

I am completely chaning setups and this is the only reason I am getting rid of these parts. All work flawlessly! Up first is a McLeod blow proof bell housing that has literally 50 miles on it. It is $409 + shipping from most retailers. I even have the instructions as well as all of the...

I am changing engine setups and this is the only reason I am getting rid of this setup. It works flawlessly. Set of 2003 Cobra valve covers, 36k miles, minor blemishes here and there, no signature sticker, and oe cobra cop covers sold COP conversion harness bought off of SVTP sold 8 2003...

I have a 97 Cobra intake which is in good shape with very minor blemishes on the hat. It comes with all the bolts associated with the upper and lower intake, hat gasket, almost new FRPP IAC, and the hat has been lightly ported to accept bigger throttle bodies. SOLD Also, I have a set of...

I have a BBK Power-plus dual 65mm throttle body WITH Throttle position sensor and mounting hardware up for grabs. These run $349 from most retailers without the TPS sensor. I am looking for SOLD

For: "Ford Mustang 1996 - 2002 4.6L V8 [281c.i.] VIN V, DOHC" I bought this because I am running a lot of electronics on the car and my stock alternator was having issues keeping up. This thing is amazing. No more voltage issues and it made everything much easier. This alternator has around...

First up, a set of Gripper aluminum Caster camber plates. These are 3 bolt, with no bearing slop and when were removed recently were in great working condition. Looking for sold Second up, and coil over setup that was on the back of my car when I bought it. I am not sure of the brand or the...

I bought this maf setup when I was going to change maf setups. Long story short, when I dug into the car many other things needed to be fixed which ended up with me switching setups. It is a Pro M maf spec'd out by Kurgan Motorsports. It is good to around 900whp in a 3'' tube. It is set up...

For sale: Paxton Billet Fuel pump which is made for them by Aeromotive. It is -10 in and -10 out that flows enough fuel to support 1000+hp. This has low miles with typical wear from changing filter elements but runs like new! Also, mated with this pump is an Aeromotive pre filter that is...

97 Cobra valve covers with chrome plug wire covers. They are scratched towards the rear. Has rub marks as well. Good repaint project. SOLD Resurfaced 97 Cobra 8 bolt flywheel. Light surface rust. $40 shipped 96 Cobra 8 bolt flywheel. Needs resurfaced. Not pictured. Offers? 97...

03/04 T56 bell housing in very good shape. Low miles. SOLD 03/04 T56 oem cross member. Low miles. SOLD 94 GT T5 crossmember modified to fit a 96-98 Cobra T45. Bolts right up. Great for DOHC swaps. $50 shipped

I have an Abaco DBX 85mm maf with harness for 96-04 mustangs. This is lightly used. Abaco Performance LLC sold Also, I have a lightly used 90mm LMAF... SOLD

First off, I have a set of verified working mark 8 COPS. 2 coils have been replaced with ford part numbers but like any other COPS, the stickers fell off. Some still have the stickers on top. They have BRAND NEW internal wires and rubber boots. SOLD Next up, I have a MSD DIS 4 ignition...

I picked up a set of 8 COP's off of a Lincoln Mark8... Went to take the boots off and replace them and I noticed that two of my coils have different part numbers than the rest of them... I assume they had been replaced at one time. I have EE03A F7LU-12A366-AC (6 of these) 2C6U-12A366-AA...

The only reason I am selling these parts is that in my current motor that is in the car made more power than I expected and I am content with its power level and I need to put a new transmission in the car. This item is a seemingly unused AEM injector driver. See pictures for part number...

High HP 4v parts (cnc heads, rods, cams, inj driver, etc) Updated +pics & more parts! First of all, I want to say that I've been in the mustang community for quite some time and appreciate everyone that has done business in the past with me. Thank you! The only reason I am selling these parts...