Search results

anyone know how to figure it out? I am dealing with a down hole motor that when you flow 350 gallon per minute through it, you have 600 hp. I need to figure out the horsepower per square inch.

What all dyno tuners are around the DFW area. Thanks all for the help Steve

I am trying to set my fuel/air ratio buy using a temp gauge on my header. I am only trying to do it this way untill I Get down to the dyno and then he can fix it the rest of the way. My question is what should the temp of the exhaust be right behind the header flange is the a/f ratio is...

So what do you guys think? It is still really rough, I tool all the big stuff off with a drill press, and now I am going to use a dremal to make them even. I took alot off the intake side, but I did not go anywhere near the bearing housing.. Comments, advice....please

how much boost should I expect?? How much boost should I expect to see from this setup? Also what kind of hp/tq numbers do you think I will see with this set up? 2.8 upper, 6# lower, stage 2 heads, stage 2.5 cams, ported blower, LPF power plenum, SBTB, long tube headers, and no cats?

Sorry the Pics are so big.... it says, TR 280 Is this the stock upper pully? It messures 3 1/4 from lip to lip.....I only ask because it does not look stock, there are two washers under the main bolt, and I do not think that it would be made that way from the...

I just spent way toooooooo much money @ LFP, but Mark cut me a great deal, at least 1000 cheaper than everyone else.... Mark, thanks.....everyone on here needs anything go to him, VERY VERY good customer service!!!!!!

I am getting my heads, but I cannot decide. I was told by someone that the heads LFP sells are junk (another vender, but a friend of a friend). I think he might be trying to sell me his heads, but I wanted you guys' option. Does anyone had any complaints about them? I believe they are patroit...

Anywhere in the US, I want someones blown motored lightning.....e-mail me [email protected]

man i wish there was some in witchita falls that liked to spin a wrench.... i sure could use the help..... :beer: :beer:

I want to remove the AC, does anyone know how to route the belt afterwards???

while doing the motor swap, i would love to get rid of as much of the crap under the hood as possible......what all sensors can i have my tuner delete?

hey you guys I seen a pic on here some time ago of a guy with a red L that had twin turbo's and it looked bad ass, do any of you'll have that pic? I did a search for it but I could not find it. thanks

look what I started today, updated I started pulling my motor today :rockon: ...Man there is alot to do here. When I am done you will not be able to find 90% of the wires, or vac lines :rockon: 5 pm 530 pm 6 pm 7 pm 7 pm 830 pm 830 pm

I am going to start pulling my motor really soon Should I leave the trans bolted to the motor and pull them together, or unbolt it from the motor and leave it in the truck? What would be easer? I have done it both ways on other cars, what is the easyest way for our trucks?

Anyone with one please let me know...It is for an 02 lightning

Hello all, I would like to buy a kenne bell for my 02 lightning.....Please PM me or e-mail me at [email protected] Thanks all for your time..Steve

What type of breaks r u running? They look bad ass....would you buy them agan or go a different way? thanks for your time..... :beer:

Where did you buy your KB and how much was it. Thanks to all!! :rockon:

Ford-trucks.com SUX Man that place blows, it is no where as cool or as informtive as this sight. I think there might be like three people overthere that even own lightnings. I am glad there is a place like this where we all can get together and share about a bad a$$ truck. Damn I love...

I do not want to run cats. But doesn't the truck's computer take reading from the o2 sensors to run correctly. Are any of you running no cats? If so how did you fool the computer into running correctly.

Hey guys, my motor is almost ready, but now I need to decide what cams I am going to run. What are you guys running, what is your powerband, r u running a stall converter and what rmp? BTW, I am going with a whipple.

What head you guys running. I am going to get different heads/ cams while the motor is out anyways. I think I am leaning tward the KB. So I need some advice, what heads/cams to run with a built short block, and a KB? thanks for the help!!! Steve

happy new year

Is there anyone on here living close to wichita falls, tx. I would love to meet another L owner.