Im parting out my entire drivetrain and going with a completely different setup. Everything below has got to go.....Feel free to make offers.
-T45 Excellent Condition with 30k miles on it, comes with a Steeda Tri-Ax Shifter - $350
-03 Cobra 11lb Aluminum Flywheel - $125
-Spec Street...
I just bought this kit and now I'am selling the car, so there's no need to keep this kit. Its got a fresh Garrett GT4088 Turbo (turbo is basically brand new, $1000 value.) Its a .72 AR Compressor Housing and 1.12 AR Turbine Housing. What you see is what you get.
This kit ALSO includes an...
Im selling my Terminator Cobra street/strip car with the following mods:
Powertrain & Performance:
Whipple 2.3 Gen 2 Supercharger w/ 3.00” & 2.75” Pulley
LFP Idler Pulleys
Meziere Electric Water Pump
SCT Big Air BA2400
Zone-5 Stage 1 FPDM
Dual Ford GT Fuel Pumps
Fluidyne Radiator
Afco...
Long story short and sweet:
Got in it to try to start it, hit the ignition and then my finger slipped off the key so it bliped. Tried to start it again..NOTHING (not even a click from the solenoid).
Found 40A Starter fuse #3 had broken. Replaced the fuse and tried to start the car and the...
My High Maintenance POS is at it again! This time it wont start. I got in it this morning and cranked it, it cranked for a few revs and then my finger slipped off the key. I went to crank it again and nothing happened, not even a starter click!
I was thinking a battery, but it seems to be...
I just got a Hellion kit without the K member and of course I need a tubular K Member, but do i also need to get the coilovers and a-arms with the K?
Aside from extra cost, I want to keep my Kenny Brown suspension and stock A-Arms since its a street car.
Thanks,
-Geoff
Check out the new toy thats going into the E.Green 99!
Its got a GT4088 turbo and once my built motor is longblocked then Ill start putting it togethor.
Im looking to make 800+rwhp on 100 or e85, any suggestions on what blow-through MAF setup to use?
I was considering the HPX PMAS in a...
Im selling a slightly used Bassani X-Pipe 2.5" Stainless Steel with High Flow Cats, it will fit all 99-04 4.6s. The unit was on my car for 6 months and about 8k miles. It has minor scratches on the bottom of the cats, but other than that its perfect.
$350 Shipped.
-Geoff
Up for sale is a recently built 4.6 Shortblock. It was built this month by HBR in Las Vegas, NV. Spec are below.
.020 Over Teksid from 94 Lincoln Mark IV
Ross -16cc Dished 2618 Forged Pistons
Manley Forged Rods
Forged 8-bolt Cobra Crank
Melling Billet HV Oil pump
OEM Water Pump
New Freeze Plugs...
Im going turbo soon and need to sell my V2-SQ E-Trim Vortech Kit.
The kit has 8k miles on it and everything with it is perfect. The kit was purchased new for $4600 and I would like to get $2500 shipped for it.
Please feel free to inquire!
Out of no where my temps sky rocketed. The coolant started spilling out of the radiator reservoir and it was blowing out a lot of pressure. I thought I got some air in since my crossover cap had a little lick.
Any way to play safe, I changed my thermostat for a new one and proceeded to bleed...
Im selling 2 excellent condition Steeda Ultra Lite Chrome rims in 17x9. They both have very little use. I will sell for $300 or Trade for some 15x10 Weld Prostars.
One rim comes with a tire.
Im doing a bunch of Gauge installs and need a single 12v power to the instrument panel switched by the headlight switch.....Anybody know which color wire and where in the dash?
Thanks in advance,
-Geoff
Just now I was driving and gave the car some gas, went to switch gears, put the clutch in ...either the cable snapped or it came off off the actuating arm.
Has this happened to anyone before?
Ill lift it up tonight and fix it, but Im curious as to how such a basic clutch setup can fail...