the only thing i hated about my cobra was the location of the shifter. if it wasnt for that i would have probably kept the car. it was annoying leaning forward to shift all the time. lol kind of a small complaint, oh and the t-56 was a bit notchy. Other than that an amazing car.
I sold my cobra to a buddy and he is going forward with mods and wants to go E85. I believe it has a SCT 2 bank chip in it right now. need someone that can tune that for a pump and e85 tune. any chance a flex fuel sensor works with that setup?
thanks
jason
I believe it is time to sell the cobra. I never thought i would sell it but have been looking at GT-rs too hard recently and think it is time to make room for one. So it is up for sale. Car is in excellent shape interior is perfect exterior is in great shape some minor imperfections but no dents...
I bent the Yoke had to pry it out. Is there a stronger one? looking at the splines they have a wave to them. I am not sure if i damaged the spines on the tranny as it came out with a little force but dropping the driveshaft i had to pry on it to push it forward. ie would not go in tranny, so i...
Hey guys I just went to the track last weekend and ran a 11.88 at 128.4 mph. i was on Hoosier drag radials and had a lot of wheel hop off the line so only a 2.0 60ft. my question is in regards to mph. is that about right for a full weight IRS car dynoing at 620-620 rwhp? or am i going to see a...
anyone taken it off? how is the connection? is it keyed or can you place it back on in a different position? long story as to why i need to know
thanks
edit: wrong section sorry mods... can you please move
I have an 03 cobra, it came with a dual tune chip from SCT. How do i verify it is from SCT and how do i data log and tune if i want? any ideas where to find info on this?
thanks
ok i got it all hooked up car runs fine with it installed. i cant get it to activate though. I tried grounding the blue wire to chasis... the LED is on all the time. in the instructions it states it should be on when active any ideas?
Probably got 10k on them. I can post pics if interested, input shaft has some wear on the splines due to a retainer breaking, it is on the very end though so shouldn't affect anything. 350 local if possible
Like new slightly polished even. Bought car with it on, previous owner stated it was on car for less than 6mo. I would like it picked up if possible , I'm in Valdosta GA.... 550 obo
Just put them on the car they have 100 miles on them tops... to noisy for me. they are not real noisy but not my thing. anyways i paid about 500 plus shipping for the setup... springs are 12"-200. 425 shipped
no pics as they are still on the car I do have some installl pics i can send if u...
Ok I put a new K-member in with a-arms and bump steer. here is the situation the steering wheel is off 90 degress. I am bottoming out one side on the tie rod and the other side it seems i will run out of rod before the wheel is straight.
Does anyone know if the stock steering shaft comes...
Ok in process of putting a Team Z k-member in... everything back together but the spindles, bump steer and struts. When tightening the castle nut it goes way below where the cotter pin hole is. and doesnt tighten up. I am thinking they sent me a fox body a-arm? i measured the a-arm and it seems...
ok I have searched and searched and think i may have an answer. I just put in a RXT clutch. i placed the pivot ball 4mm towards the transmission. I have the firewall adjuster all the way in and the clutch releases around 2 inches of clutch travel. so at the very top. I havent driven car yet...
:beer:A week and a half ago I flew up t0 NJ to pick up a cobra. test drive was fine and i started driving it home. 500 miles or so into the trip the clutch got a little notchy. 800 miles in the TOB got noisy and when i pulled into my buddies driveway it was rattling like crazy. so I left the car...
Ok so taking everything apart now, tob was making a lot of noise. Turns out retainer was broken. I am still in the process of trying to take out the third starter bolt! Dam that thing sux! Going to store for different size extensions... Hope it works out.
The 26 spline I have has 1.5" of...
do you guys know if they will fit? or vice versa? i need to borrow a buddies wheels he has an 05. i have a 03 cobra. just need to drive the car home on them but it is a 1k miles interstate...
thanks