I was going to ask this in the S550 section, but it’s completely full of ads. So I am defaulting to the cobra roots.
I am doing a Gen 3 coyote swap with a Gen 5 3.0 Whipple on the car. Collecting parts and got wondering about the IC system on the S550. I know a lot of work has been done over...
Just wanted to post this questions for the guys with Whipple Crusher inlets. I just got back from driving the car and laid into it a few times. Noticed after the one pull my idle was hanging a bit above 1000rpm.
Get home, pop the hood and notice my TPS sensor is cracked right in half. Looks...
Been doing some searching and was wondering how you guys with them have wired them up.
I have a relay for the line lock in my engine compartment already that powers the line lock. I was using a 3 pronge rocker switch inside the car to turn it on, but I installed a double din receiver so lost my...
Just wondering if anyone has the part numbers for the two blue canisters that drop into the fuel tank. I am able to find just a single canister on LMR or Ford Parts.
I messaged Steve@tasca parts on here and no reply? Is he no longer around, he was usually my go to for stuff. Was looking to grab...
I am going to try and finally get on the E85 train, but doing some research and not sure if I am screwed or not.
I have a Glenn’s sumped tank with triple walbro GSL392 pumps. These appear to be not E85 compatible. I have had this setup since 2007-2008 when I first went return.
I have been...
I mentioned in another thread how I developed a clunk while getting started from a dead stop or just clutch out and in on a flat surface, moving up my driveway, etc.
I tried to replicate it with the wheels off yesterday to grab a video. With no load its silent. So I put the park brake on and...
I have been hunting around social media for different wheel ideas and came across this meme and did a double take. I was like wait a minute, that's my old engine bay photo! Funny how you find stuff just randomly used. Be curious to find who made it.
Does anyone with a convertible know if you can use the convertible switch from Ford (F4ZZ-15668-B) to activate a line lock or just send power to a relay?
I would like to replace my coin holder with the above switch if it will work to control my line lock. I know people prior were using the...
So I have been searching forums and Instagram trying to see what people are running for 18" wheels that aren't CCW, HRE, Forgeline, True Forged, Boze. I am basically looking for wheels that aren't going to run me $3400-$4000 US. I like the chrome/polished look and from some checking polished...
I am struggling to figure this out. I am trying to log the pressure drop across injectors PID in livelink II with my X4 and all I keep getting is a value of 0 in livelink.
However if I use gauge mode on the X4 handheld and select pressure drop across injectors I get the value of 50psi that I...
I was going to dig up an old thread from 2008, but decided its too old. Thread is here - https://www.svtperformance.com/forums/threads/cobra-r-brakes-are-not-enough-so-i-installed-a-brembo-gt-kit.467268/
Anyways I am thinking about attending a few 1/2 mile events in the next year and wondering...
So I have been having some issues with getting my car to idle.
Newly added mods to my motor are a crusher inlet on my 3.4, VMP big TB and ID1000's.
To get it to start and not drop rpms and die I had to unhook the IAC, open up my Throttle blade until it would idle on its own with no throttle...
Looking for a coolant cross over pipe from a 2003-2004 Cobra or even a 2003-2004 Mach 1.
Please PM me if you have one. Tried searching this forum but apparently "coolant crossover pipe" is too common to actually search :mj:
Thanks
So I decided to post this here as anytime we throw something in the Mach 1 specific section it gets very little attention.
This is for my brothers 2003 Mach 1.
Car info:
Solid axle in the rear still with MM extreme duty rear lower control arms(spherical bearings). MM full length subframe...
Just curious whos kit you are all using and if you happen to know who has the stronger/beefier kit available.
I don't hear much mention of the Tie Rod kits so thought it was best to ask.
Bruce's FTBR kit part FT-1860 - The Finest IRS Delrin Bushing Kit
MM IRS tie rod kit - IRS...
I would like to remove my front and rear calipers to prep and paint them with the G2 paint kit. When I disconnect the lines does anyone know of a fitting or cap I can buy to plug the line so the fluid doesn't all drain out?
I figure I will need to leave the calipers off the car for a couple...
I was told not to bump old threads before so I will ask this question in a new thread.
I know the MRT hood struts open the hood about 1" less then stock. Does anyone know what the redline struts open the hood compared to stock.
I am in the market for a set of hood struts and I am just...
I just wanted to ask what you guys have been running lately and how they are working out. What I mean is noise level, ride smoothness, etc.
I have 275/40/17 BFG KDW's on the front now and I am only replacing them as they have cracks in between the treads on the outside edge so I am getting a...
I remeber seeing a video a while back(I think on this site) of a license plate cover that when a current went through it the filiment in the cover would go opage(white and block the numbers and letters). It was hooked up to a switch and you flicked the switch to cause it to go opage.
I know...
I just wanted to ask if you guys could help me out. There was a video posted on here a while back of a GT500 racing a turbo'd Camaro and the two guys filming it where in a GTO I think.
The guy filming had the best line of "this mother ****er is balls to the wall baby"
If you remember the...
Well I got the car dyno'd up in Edmonton(2 hrs north) on Friday. Blower is running a 3.5" upper and Metco 6.55" lower and I am seeing 18psi with that up here. Sea level it should be about 21psi. With pump and torco this is how the car did. I should have pulled it a little higher, tach was...
Can you guys help me out, I am installing this for a friend and there are no instructions with it.
It has the drain **** on one side and the two outlets on the other side. It also came with some new long hoses and this is what is screwing me up the most, I am not sure where they go.
TIA
Well I finally got finished up with my new mods. Here are some pictures and a quick video of a 1st - 4th gear hit on some 315/35/17 nittos. Its running right off the X-pipe right now due to not being able to get in to have the v-band clamps installed on the catback to join my stingers up to...
Well I came across this thread on Ricekiller.com about a guy in a viper(TT) running 10.94 @ 140mph on "street tires" as labeled in the video. Well his street tires are drag radials.
Do you guy call drag radials a street tire? People are saying because they are DOT approved they should be...