I have a '96 GT with a full terminator swap done several years ago. I am running the '96 return fuel system. If I turn the key and wait a couple of seconds for the pump to run and then turn to start, the engine fires immediately. If I try to start the engine without doing this it will crank...
I am coming up with these two part numbers for an OEM Alternator replacement. Has anyone purchased either one and can confirm proper fit. If you have a different number let me know.
4U2Z-10V346-EKRM or YR3Z-10V346-ACRM
Thanks
I am using the article "Re-wiring the Cruise Control Buttons to Control your Radio Volume" from Mustangworld Mustangworld - Radio controls Mod to tap into the cruise buttons for use on a Kenwood DNX693S. The purple wire for volume up is not there. Blue, Black, Grey, Yellow and White/Brwn. Blue...
Looking for a 03/04 Cobra Gauge cluster for parts. I specifically need the overlay section of the cluster that has the indicator symbols on it. Let me know what you have.
Thanks
Buzz
I have Bilstein Sports with MM coilovers on my SRA rear. I have 30K miles on them. They seem to have lost some of their compression dampening as it appears that I am hitting the bump stop now on some bumps in the road that I hit regularly. This has become worse over time.
Is it possible...
I have the strut tower brace from my GT that is in great shape. If anyoone wants it I am in the North San Diego County, CA area. Come get it. PM me
Thanks
Buzz
What is your voltage reading at the Aeroforce gauge compared to checking it at the battery. I am seeing about .3-.5v difference between the idle voltage at the battery which is about 14v and at the gauge which is any where from 13.5-13.7 or so. Is this typical?
I finally installed a double din Kenwood deck in my '96. Has Nav, ipod integration and bluetooth phone integration. Also installed a Mach 1000 sub powered by an Alpine MRP 350 amp. Sound is so much better that the stock headunit and with the sub it is really good. I was going to replace the...
I am told the reverse lamp wire that goes +12v when the car is put into reverse is in the front driver kick panel. Does anyone know which wire it is?
Thanks
In another post a member suggested that in most custom tunes the IAT2 temp when timing is decreased was 140 degrees. I had thought about increasing the threshhold at one point a bit as mine is set at 100 but 140 seemed very high. Does anyone have a custom tune where it was set higher and at...
Can anyone tell me if there is a Low Coolant Sensor on the Terminator and if so where is is? I don't believe there is one but I may have missed something. Looked through the Service Manual and I see no reference for one.
Anyone know of a way to dim the aeroforce gauge at night less than the low setting. Still too bright at night compared to the other gauges. Anyway to make the dimmiing adjustable?
Thanks
Does anyone know whay the ABS light comes on after an aftermarket HID install. Last year I installed a Bi-Xenon 9007 system from HidGuy.net. Rarely I got the ABS light after turnng on the lights. No real problem....
I recently went to D2S bulbs and projectors from the retrofitsource.com...
Anyone use this fuel pump in their return style system. The site is saying it will support 700 HP. Looks like a good upgrade to the 255 Walbro I am using as I gather parts for that 2.9 Whipple upgrade. Do you think this would support a 2.9 Whipple?
Bosch Fuel Pumps - BoschFuelPump
I want to have the low threshhold where the ECM pulls timiing due to Air Charge Temp (IAT2) raised. Presently in stock form it begins to pull timing at 100 degrees scaling to 150 degrees. I was planning to have this put to about 120 degrees and scale to 160 degrees. 91 Octane fuel and 13.5...
I just installed an Aeroforce gauge.... great product. The directions indicate the extra 12v switched source is not needed which is true. One issue that is not made clear however is that the gauge draws about 50ma and will drain the battery if left hooked up for an extended period without the...
I just installed my new Aeroforce gauge. Best gauge so far..... anyway my Throttle Postion won't read above 92% even after adjusting the TPS idle voltage to .99... was at about .71 at idle. Whan at .71 it would read 90% at WOT. Throttle Body is fully open when accelerator is depressed to...
I purchased the Sequential Turn signals from a new vendor Autotrix and I am having problems with the kit. I have emailed them three times with no response. Does anyone know how to get a hold of these guys?
What would make it difficult shifting into first gear when the engine is running. When engine off it goes in fine.... this just started happening.
Thanks
Does anyone make a projector headlight housing that will accept the single bi-xenon bulb from the HIDGuy kit or similar. I like the Depo Chrome projectors but that is a dual Low beam only and takes the 9005-06 bulbs I believe which I don't think will fit. If the 9007 would fit in the Projector...
I am running a return style fuel system and have the tune setup for this. Does the Fuel Rail Pressure Sensor have any function now and if I were to disconnect the vacumn line to use for a better Boost by Pass vacumn source would there be any negative effects.
FYI
I had a noise in the rear that developed after some time with the MM coilovers. It sounded just like an exhaust pipe hitting something when you would hit a bump. I checked everything and after months finally found it...
It turned out to be the top of the Bilstein shock, the nut that...