Search results

[Sold]

I recently purchased Coastal's Lockpick for my car primarily to run an aftermarket license plate bracket rear camera and have full use of navigation functions while driving. Pretty neat that it also allows you to install a front camera (something nice when you're parking and you don't want to...

I know there have been quite a few guys waiting for Craig to fab one of these up. He stopped by last week to take measurements and came back today with a pre-production version for fitment and finish. I have to say it looks great and I can't wait for him to bring it back from the...

Had it lifted last week and the weather finally cooperated so I decided to clean it up and snap a few pics... Setup... - Fabtech 8" four-link kit - 22x11 Moto Metal 950 wheels - 37x13.50-22 Toyo Open Country M/T's I bought the kit used, so I have to replace the...

The last time I dyno tuned my car (by Ed Clark) it was breaking up on the top end and he suggested it might be the plugs...fouled and/or gapped improperly. Previous owner installed NGK TR7ix (Iridium) plugs and had them gapped about 0.032". Today I replaced them with NGK TR6 plugs gapped at...

FS: '04 Oxford White convertible, 2.8H KB, 600 rwhp, 20K miles, $24K, Virginia... *** SOLD - SOLD - SOLD - SOLD *** After test driving the new 2010 Mustang, I'm sold and looking to get rid of my Cobra to pick up either a GT500 or Roush Stage 3. Thinking about going back to a coupe as well...

I called on the tuning services of Ed Clark and we used the dyno at All Aspects Motorsports in Chesapeake, VA. Very satisfied with the new tune. It looks like my fuel issues were resolved with the Lethal wiring upgrade. Also, Ed was able to get the idle smoothed out and now idles much...

Looking to increase torque and in need of a 4" upper pulley to fit a KB 2.8H blower and any brand 4 lb lower pulley assembly. I have a Kenne Bell 3.5" and 3.25" pulley for anyone interested in trading pulleys. Reply to thread or shoot me a PM. Thanks...

I had my car on the dyno on Monday and we saw dangerous drops in fuel pressure above I'd say 4,000 rpm's. It was dropping as low as 22 psi. The only thing I don't have installed is the wiring upgrade. I purchased it after leaving the dyno and started installing it today. The directions off...

I purchased new wheels and tires for my car and need to get rid of these. Previous owner purchased these wheels and tires for my car not too long before I purchased from him. They look much better in person than in pictures. I just needed something that would hook better for my power level and...

Sorry, it was late when I finally got the tires mounted and wheels installed on the car. I'm going to try and snap some better daytime pics tomorrow...

Anyone running 17x10.5 Cobra replicas with 315/30-17 M/T ET Street drag radials and having rubbing or clearance issues? My tires come in tomorrow and I'm getting them mounted up. I remember a few people mentioned having to grind down the bolt, but I can't remember if that was for 335 and...

The previous owner actually purchased the Spec Stage 3+ steel flywheel and clutch from Lethal Performance and provided the kit to me when I purchased the car. I confirmed through the Spec website that both are the correct part numbers for my car (SF84S steel flywheel and SF873FT clutch disc and...

Threw the car up on jackstands in the garage about a week ago. This past weekend I got quite a bit done. Installing the following: - Spec Stage 3+ clutch with steel flywheel - Liberty 26 spline input shaft - LDC cooling mod - TO bearing retainer sleeve - Fore billet fuel hat - Fore...

As the title states, selling the old exhaust system from my Cobra. Took both pieces off last night and ready for someone to come pick them up. The MAC cat-back is model number MAC-TK4699 (2.5" system with 3.5" stainless steel tips) that normally sells for about $375. The UPR is model number...

I ordered a set of GT pumps, modified FPDM, fuel line adapter for the Fore Precision fuel hat, and a set of Fore Precision fuel rails with the fuel rail fitting kit. I ordered over the holiday weekend and arrived today, Wednesday. Everything came except the fuel rail fitting kit. I went...

Purchased this car a few weeks ago off the classified forums on this board from Junebug1. Today I took it to DTP Racing in Chesapeake, VA to get the blower looked at and threw it on the dyno to check the A/F. The blower (leaking oil) looks to be an easy fix and the previous owner informed me...

Just as the title says, I am looking to purchase a styling bar with the LED light. I am looking for a bar in dark charcoal to match the interior of my car. Thanks!

Same information can be found here...PAS Ad Selling to pick up an 03-04 DSG Cobra 'Vert... Pics can be found on my CarDomain page here. Year, Make, Model: 2004 Saleen Mustang S-281 SC #091 Mileage: 6,094 miles Asking Price: $26,000 Last four VIN: 2319 (for authentic Saleen...

Like the subject line says, I'm looking for pics described. If you have one, please post it up. Trying to see how it would look. Been thinking seriously lately of selling my Saleen and picking up a black 03-04 Cobra coupe. Thanks...

I'm in the market for an 03 or 04 Lightning in either Sonic Blue or Dark Shadow Gray (DSG). If you've got some good pics...please post them up! Thanks in advance... :thumbsup:

I know the video is old, but I never looked at the hood of the car before until this repost on another forum. In one of the videos the officer states he is in an unmarked Cobra. Traffic Stop Taser Video You need QuickTime to view the video.

I got back recently from overseas and did some engine mods to my car. After the dyno session I cleaned it up and snapped some pics... Oh yeah, car made 361 rwhp / 392 rwtq. I'm pretty happy, but still looking for more power. Pics of the car... Pic of the new Kenwood Head...

There was a guy on here who found a shop to do the F'in Fast Shift Knob. I believe it was out west somewhere...Arizona, maybe? He also had a custom 'Eject' button cigarette lighter. I'd like to get the information of that shop that did the work. If anyone else got this shop to do it...please...