Search results

Hello everyone, I bought a spec 3 clutch and aluminum flywheel with intention of putting them in my car. However, I have been reading on RST clutch and was wondering if it would work with the spec flywheel so I don't have to buy that as well. Thanks

Need help knocking out Paxton 2200 input shaft ring. It looks like you put large socket over and bang out. My question is how to put back in w/o damaging. Thanks

Hello all, My belt broke and wrapped around sc shaft. I went to change pulley and noticed oil coming out. I took lid off sc and took pieces of belt out on inside. Bearings all look good. I can’t remember order of 1 flat washer and 2 spring washers on shaft?? Any help would be appreciated.

Hello all, My belt keeps skipping over 1 rib towards motor. My question is there a spacer that goes behind blower pulley that pushes pulley out 1/16”?

Hello everyone, I purchased the torque booster from beefcake. However, I currently run the stock 3.8 on my Paxton. It has torn the belt twice. It seems to be off by one rib closest to the motor. Anyway, now that I am upgrading I wanted to go with the 3.25 pulley because it has a lip to keep...

Hello all, Just wondering if 305 45 17 drag radials fit on 2014 gt track pack. I see a lot of 2015 and up with them but not s197. Thanks in advance!!

Hello guys, Right now I’m running the 3.6 with 48# injectors. I am wanting to switch to 3.33 w torque converter. My question is can I change belt and pulley and drive car with the 48# then change to the Id 1000 when I get to dyno?

Hello all, I have tune with cats included but I can’t get car to be emissions ready. I was wondering if I put stock injectors on and stock tune. If I stayed out of boost could I pass that way? Lost, cat has been down 6 months…please help:)

Hello all, I have 2014 mustang gt w Paxton 2200. Currently running 47# injectors w BAP and 3.8 pulley. I am wanting to install ID 1000, DW 400 in tank fuel pump, and 3.33 pulley w torque booster. After I install these mods can I drive to dyno w current tune??

Hello, Anyone have a 3.33 pulley for sale?

Hello all, I have Paxton 2200 with 3.8 pulley, 50 mm Tial bov, 47 pound injectors. Have the Breenspeed Stage 3. Installed kit ran good for about 6 pulls. Now every time I try to mash pedal it bogs at 3k rpm like not getting enough fuel. I hear lots of popping in exhaust and power decreases to...

Hello all, I took my rtr decklid off and going back to gas can rear deck lid. Does anyone know the size of the two screws that hold on stock decklid?? Was going to make trip to ace hardware to pick up a few screws??

Hello all, I am running Paxton 2200 on my 2014 gt. Boost is only about 8 psi w 3.8 pulley. My Tial blowoff is not going off I assume the spring is too big as last guy was running a 3.33 pulley...what is the correct spring I should change to??

Hello all, I was putting the short 47 injectors from a 2010 gt 500 and I noticed orange strip. However, on the websites that sell shorty 47 I noticed yellow strip. Can someone with OEM injectors way in??? Thanks

Hello all, I just installed 2200 paxton on my 2014gt. I went ahead and changed supercharger oil before installing. My question is how the hell do I change it next time. I had to take pipe and throttle body off to access lower nut with dipstick? Is there an easier way? PS. If anyone does...

Hello everyone, I just finished install of 2200 Paxton on my 2014 gt. I tightened all bolts checked all pipping. However, when I went to start it just keep turning over but would not start..then the lights flickered and clicking noise like battery dead...I checked it and it was at 11.5 so I put...

Hello all, I will finish install on my 2014 gt w Paxton 2200 on Tuesday.....waiting on an o-ring for boss intake from Vortech. My question is am I safe to drive to Dyno shop 12 miles away or do I need to tow car there???

Hello all, I’m installing Paxton 2200 to 2014 mustang gt. I was about to put blower in and the pulley is too small 3.33....I have a 3.8 I need to put on but can’t seem to break bolt on blower. I put some vice grips on and pb blaster and I can’t budge....I was going lefty Lucy is that the correct...

Hello all, I was looking at buying 17” race stars w et streets. What tire size should I buy rear. I have 14 gt with track pack. I want a size that performs but also looks good when not dragging:)

Hello All, A friend of mine was selling his Vortech V3 kit off of his 2015 mustang gt. I was wondering if it would fit on a 2014 mustang without too many modifications or having to buy new bracket etc....

Yes, I know it’s a long shot but I’m wanting to buy a Vortech bracket for coyote. I have an old v3 head unit I was wanting to put on. Thanks