Search results

just curious what you ever did for this issue. I have same exact issue with my car

Selling this for a friend. personally removed for turbo swap. 4.0 kenne bell blower went 8.0 174 in renegade legal 2012 cobra jet. The car is on Kenne Bell website also. The blower comes with big gun rear manifold also big gun throttle body. I will include the original elbow that will work with...

I know fr500 cams are not the best but came across a great deal on them. I want to do the cams with livernois springs. Has anyone ran them n/a witH any good numbers? Would it make 350 hp with all bolt ons? Car has already made 318 rwhp with stock cams and na svt ported lower. Car currently has...

Here is what I got guys. I bought this driveshaft used a while ago from a guy on here. It was in my 1999 cobra then swapped it into my 02 GT with irs. I am now selling the 02 GT so i am selling some of my mods from the car. I do not have the cobra flange but comes with yoke. The driveshaft...

I am looking for a aluminum bell for a Tremec 3550,tko etc. Let me know if anyone has one. thanks email if easier [email protected]

I thought someone had this combo. I did a search can't find it anywhere. I am getting ready to put this in my 99 Cobra. Hoping for 350 rwhp. I may have to go back to 4.56 gear. I would like to see this go 11.50 with some wait out of my car.

Just installed 4.88 gears in my 99 had 4.56 gears using 15x10 welds 26x10 m/t et drags 60-1.627 normally goes 1.57-1.59 330-4.920 1/8 7.671 89.65 best ever 10.021 1/4 12.009 113.16 so so close. I still have my factory wheels on the front swapping to skinnys for next trip...

mods are full exhaust, xcal 1, pulleys, cold air, and a straight axle 4.56s full weight car 17s up front 15x10 welds in rear. went to cecil county today hot 85* plus temp put slicks on the car normally run a 275/50 hooiser mounted up a set of 26x10 et drags. previous best on a drag radial was...

I have a lightning meter now is there any adapters the the electrical connector or any sleeves needed to work with an wms cold air.

all you n/a guys what clutch/trans are you guys running mainly with drag radials. I currently have spec stage 1 with t-45 but and thinking of switching clutches.

Everyone says the 03/04 mach 1 lowers flow the best of any non-ported n/a version 4 valve. I was wondering if anyone has put a non ported 03-04 mach 1 and picked up any power.

99 cobra usual bolt ons shifting car the rpm will rise as soon as clutch goes in. Load doesn't matter it does it all the time.seems to get better as car warms up. Could it be a vac leak? Anybody? Thanks guys

I have a steeda timing adjuster that I no longer need bought a chip. $75 shippedThanks Good for 96-01 cobras and 96-04 2 valve Thanks From Tom

best run was 60-1.868 yuk 330-5.358 1/[email protected] 1000-10.579 1/[email protected] mods full exhaust bassani mids,steeda underdrives wms cold air 4.56 straight axle 275/40 m/t drag radials also should i put a 275/50 m/t drag radial to get some better 60s? one last thing should i...

I have a 99 cobra has underdrives and an electric waterpump. New battery alt tested good amp wise on a vat40 alt tester. Charging voltage is at about 13.2-13.9. Also every once in a while the battery light flickers on and off real fast but never stays on.If I drive the car for a day by the end...

I have a pro-m 80 mass air calibrated for 42# injectors will sell for $125 shipped paid $300 Thanks From Tom

just as title says it will fit 01-04 gt/mach or 01 cobra $100 like new

i was wondering if you need to use an 03-04 cobra clutch if you use the flywheel. also what can I expect to pay for a used one 03-04 aluminum flywheel? Thanks Again From Tom

I want to buy a lower intake from an 01 Cobra or 03-04 MAch 1 let me know what you got. Thanks From Tom

I have a steeda timing adjuster that I no longer need bought a chip. $75 Thanks Good for 96-01 cobras and 96-04 2 valve Thanks From Tom

What brand and what and how low do you guys like the best when lowering these cars?

99 cobra irs 3.27 gears 70,000 miles mods: bassani mids,xpipe,catback, wms upper lower cold air tube,steeda underdrives,spec stage 1 clutch and aluminum flywheel and sct x cal 1 made 316 hp 312 torque is that lower for the mods? car made 272 hp 280 torque stock has had recall done. What do...

2 bolts are longer on the bellhousing than all the resty were do they go? Thanks

what trans fluid does it take can't get search to work. Thanks From Tom

99 cobra with 98 straight axle gt brakes so the axle is a little short. I want a 15 inch wheel but how wide and what backspacing should I run. Leaning towards the centerline convo pros. Thanks From Tom