Hello everybody I came across a new supercharger for the 2016 gt, in the install they removed the front crash bar to replace it with a intercooler mount. What are your thoughts on this??? Is this even safe??? Will it cause issues later????
Sent from my SM-A015AZ using the svtperformance.com...
Hi everybody,just wondering what company I should trust in buying my kit.heard some bad reviews so I want to avoid getting scammed. I'm in texas but I'll order from anyone who has excellent service..chime in on the company you used and how your experience went. Have a blessed day!!!
Sent from...
Hello everyone i have had my mustang at a shop now for over a year, all it needed was a rebuilt engine. Every time i contact the shop and ask for photos of progess the owner/ mechanic gives me the run around. I havnt had a single photo sent to me, when i told him i would swing by he said the...
Ok guys i dont know anything about clutches so any help is appreciated. This pressure plate was put on brand new...needless to say it was abused as well. Does it still look good?only put 5-6 miles of use on it. Should i just get a new one? Thanks again cobros
Sent from my SAMSUNG-SM-J727AZ...
Hello everyone... well title says it all, i have mcloud pressure plate installed brand new out of the box.car was driven hard,realised i had mechanical issues with motor.pulled out motor and noticed pressure plate suface had some hot spots on it.is it now a throw away??...or can i smooth out the...
OK guys u have everything out to replace clutch and flywheel. But how well do these 10 spline shafts hold up? Car had 450hp, thinking I might upgrade to 26spline. I wanted to see how much the stock one could take . interested in people's experience with it.
Sent from my [device_name] using the...
Well guys as the title says I have a warped head. Time to pull out the motor and see the damage. 1st time pulling a motor out so I'd like to go the easiest way possible, I was thinking I could unbolt the trans. And pull motor out. Is it easier to pull everything together? What have you guys...
OK guys I got either got a blown head gasket. ...but I'm pretty sure it's a warped head . either way the whole thing had to come apart. I contacted a few shops and it's easily $1500-1800. Would this be something for a diy. I mean I can take it all apart. ..but then to put it back together I...
OK guys I put in a edelbrock water pump changed out the thermostat (tested to confirm it works correctly) flushed out heater core, had aluminum tank dipped in acid to be cleaned and replaced expansion tank cap. ...but... coolant still blows out expansion tank! what could be causing this?. .I...
Hey guys I just hooked my temperature Guage. Grounded to chassis, and I hooked up the power wire to my fuse box just like my other gages..only problem is that Guage is always on.my other gages are won't turn on till I turn the key am just missing something here?
Sent from my...
Hey guys I just installed a after market temperature Guage hooked up to fuse box just like the rest of my Gages .I hooked ground to chassis and temp Guage to sending unit.but Guage stays on all the time....even without key on...no of the other gages do that. ..did I miss something. .does it need...
Hey guys u have a extra Eaton charger that I want to try porting out.is there a general rule on how much material is removed? Same goes for the case where the rotors are in, is that just smoothed out or is there material getting removed. Any info would help.
Sent from my SAMSUNG-SGH-I337Z...
OK I just finished putting my high flow water pump and just to the left right above the inner tensioner I noticed black dust....I put the belt back on a realized it was the belt rubbing :/ anyone else have this issue. Anyone have the belt path?.? Here is the pic
Sent from my...
Well just like the title says, I want to polish the valve covers but I am a little concerned there will be a increase of heat.does anyone know if it will? Anyone have them polished?
Sent from my SAMSUNG-SGH-I337Z using the svtperformance.com mobile app
OK guys I removed the water pump and it's really rusted..I removed all the hoses and more rust, even rust on the block.any safe flush to clean all that up
.
Sent from my SAMSUNG-SGH-I337Z using the svtperformance.com mobile app
Hey guys need to flush out the heater core. Does anyone know where the lines come out into engine bay? Any photos? Any help is appreciated
Sent from my SAMSUNG-SGH-I337Z using the svtperformance.com mobile app
Just like the title says..my fan was not kicking on so I pulled a part the connections and saw the connections were bad not contacting. Could I just clip off the connectors and connect the wires direct to each other? Would that change anything? Any help is appreciated
Sent from my...
OK guys after having issues with the fan replacing the fuse ,relays ,coolant sensor I'm hooking the radiator to a switch directly. The 03 cobra fan has a low and high and a ground wire.what would be best to hook up. A 3 position switch? Which I'm not sure how to wire...or 2 separate switches...
Hi every body I recently got my car back after sitting for 2 years getting the motor rebuilt. I fired her up drove it up and down the street and shut it off and heard the water boiling in the reservoir. Changed out the thermostat, it was stuck together. While doing the flush on the system I...