Search results

  1. TX_Hoonin

    wtb oem 13-14 GT500 quad mufflers

    I have some here in Dallas
  2. TX_Hoonin

    STAND ALONE ECU W/ FACTORY ECM?

    Emissions isn’t a concern for me, it was just really retaining accessory functions i.e. A/C, steering rack, windows. I knew it was possible because I’ve seen street cars running Holley EFI, AEM, etc. But it’s hard to find info on how it was done. Boomslang has an solution for the AEM system...
  3. TX_Hoonin

    STAND ALONE ECU W/ FACTORY ECM?

    So pretty much your saying if I’m using the AEM Ifinity stand alone and factory coils they have an harness for me to be able to run both?
  4. TX_Hoonin

    STAND ALONE ECU W/ FACTORY ECM?

    It was 2 months ago, but it could be because i was enquiring about a harness to be used with the Holley EFI stand alone
  5. TX_Hoonin

    STAND ALONE ECU W/ FACTORY ECM?

    Im familiar with Boomslang, but at the time i contacted them they had no harness for the gt500. You have to send your factory harness to them for modification?
  6. TX_Hoonin

    STAND ALONE ECU W/ FACTORY ECM?

    2012 GT500
  7. TX_Hoonin

    STAND ALONE ECU W/ FACTORY ECM?

    Has anyone in here have any knowledge on how to use a stand alone ecu such as AEM Ifinity or Holley in conjunction with the factory ecu so that i can retain accessory functions such as A/C, power steering, windows, etc?
  8. TX_Hoonin

    FS 07-14 GT500 CAMS

    PM’d
  9. TX_Hoonin

    Fore Fuel Return Fuel system issue

    Thank you for the reply, did you tap that wire at the FPDM or at the fuel pump plug?
  10. TX_Hoonin

    Fore Fuel Return Fuel system issue

    I've just installed a Level 4 Fore Return system in my 2012 GT500. I wired the FC3 controller and the Bosch relay exactly like Fore instructed but my pumps will not power up with ignition. I contacted Fore and they sent me instructions to revise my tune. My tuner made those revisions and the...
  11. TX_Hoonin

    KB 3.6 under stock hood

    2012
  12. TX_Hoonin

    KB 3.6 under stock hood

    Combined with lowered engine mounts? And will spacing the k member cause alignment issues with the driveshaft or issues with steering shaft?
  13. TX_Hoonin

    KB 3.6 under stock hood

    Can anyone definitively tell me if there is a way to fit a KB 3.6 under stock hood. I've seen cars online that have done it but I can't find out how.
  14. TX_Hoonin

    FRPP 52# Injectors NIB

    Sold
  15. TX_Hoonin

    ATI 10% lower

    420 shipped
  16. TX_Hoonin

    FRPP 52# Injectors NIB

    Bump
  17. TX_Hoonin

    ATI 10% lower

    ATI 10% O/D pulley from 2011 GT500, bought from another member on forum but was too much pulley for my setup so I never installed. Comes with brand new crank bolt.
  18. TX_Hoonin

    FRPP 52# Injectors NIB

    Set of 8 FRPP 52# Injectors NIB. Selling because I need more injector for my goals. 250 shipped.
  19. TX_Hoonin

    Throttle body , oil separators , intake

    JLT still available?
  20. TX_Hoonin

    FS: ATI 10% OD pulley

    Will this fit the 2012?

Top