Search results

Just installed a 26 spline fidanza clutch along with liberty gear 26 input shaft. Have what I believe is probally just clutch chatter in 1st and sometimes 2nd while taking off, all other gears feel good,hoping it will go away once broke in as its only got 30 or so miles on it, just wondering if...

installing a liberty gear 26 spline input shaft. my problem is that the bearing race for the input shaft bearing is loose and rotating in the cup of the front cover, isin't the race supposed to be tight and not move, thinking maybe I messed the cup up taking the race out to put the shim in and...

While Changing out the oil pan gasket and had engine raised and supported and k member lowered, while putting everything back together seen coolant was leaking out of the inspection hole at rear of block directly above rear main, so question is what could be leaking into the block valley, heater...

Looking for a local sell, as they are listed on craigslist, just passing along in case anyone is locally close to southern nm, west Texas in the area looking. Took my Bassani SS polished 2 1/2 mufflers out of the catback to replace with borla and don't really need them anymore, looking for 120...

Installed a aem uego lambada/afr kit. I have noticed that there seems to be a one second delay on readings? Has anyone else experienced this? Installed the sensor in front of the cats on a vrs catted x pipe about 12 inches downstream from the collector. Searching on the internet have seen...

Can you test the coil on plug with a multimeter like an old coil pack, looking on line looks like you cant use a resistance test on these, I have a circuit failure on prime A, hoping to be a bad coil.

On my way back from town today and started smelling electrical. Smoke was coming in passenger side. Pulled over and found the green wire going to the driver side wiring for the CoP was basically burned into to all insulation burned off, from looking on internet looks like this is the ground...

Thought is was the relay and replaced that, hear a clicking whenever I push the foglight switch when park lights or low beams are on but foglights won't turn off, Bout the only thing I changed was put some new foglight cases and fog lights in. Any ideas maybe a short and getting current on...

Need help on my 03, currently installed expansion tanks for coolant and intercooler, 170thermostat and heat exchanger. While performing the burping procedure coolant was leaking behind engine on ground, coolant level in tank looks normal, intercooler resivoir was bout half empty so looks like...

Picked up a 03 last year with basics, 2.81 upper, exhaust and a jlt ram air with a diablo predator tune. The previous owner didn't install a larger idler pulley so I got a billetflow 100m that I'm gonna put on with new belt for better belt wrap around pulley. Will I need to get it retuned...

Picked up a 03 dsg cobra back in Feb, car has 2.81 upper, exhaust, mac cold air and predator tune, fairly basic pullied terminator. Want to get rid of the pos mac intake with it's bend and go with a straight shot ram air JLT. Will I need to retune after this? I think a lot of my hesitation at...

Time has come to focus on my 03 Termy and get a daily driver truck, so gonna be parting with the mystic, hoping for local sale in southern New Mexico.Car has 89XXX miles and currently daily driver. Mod include the following H&R Sports, Bilsteins, MM Plates, Pro 5.0, Ram HDX clutch with...

Was gonna get a truck, dealer only wanted to give me 3K on trade in, o well, why not perfect by anymeans still 3K with 88,000 miles, maybe I can get 5 from local sale, very dissapointing, either that or repaint the car and keep it damn that's gotta be expensive.

Started last night, initially threw a 1504 which turned out to be a loose wire at the IAC, that was fixed and car idled. As long as I keep it below 3250 car idles fine so IAC appears to be good. If taken over 3250 and IMRC's open if you engage clutch to shift rpm's will drop down and car will...

Anyone ever use the poor boys wax and sealants. Heard it's Supposed to work pretty good on dark cars just curious if it's any better than the meguire's line of polishes and waxes.

Daily driver Mystic gettins some sun, cheap camera's just don't capture the color shift :-(

Anyone running the bilstein bts suspension kit? if so post some pics curious bout the drop.

although they look good, my damn bulb burned out in two weeks, thinking that these things get too hot or maybe just had a weak bulb sent with em. Gonna replace the bulb but thinking it will probally do the same thing, unless maybe I have a short? any other good clear aftermarket fog's out...

How many electrical connections are on the starter. Just finished my clutch install and starter seem to drag for bout 1/2 second? Did I miss putting a connection back on just the main terminal and the little black clip right?

Just installed a new clutch and trying to adjust this steeda adjustable clutch cable. Problem I am having when trying to take the slack out of the cable is rather than pulling the slack out it is pulling the throw out bearing up next to the fingers on the pressure plate before taking out the...

Thought I fixed the lean code as the mac cold air was a little loose on one side. Cleaned the MAF and tightened everything up and was good for several days and code returned. Starting to think it's this pos mac cai witht the bend that causing it at part throttle. Thinking it's time for a jlt...

ABS light is staying on. Topped off the fluid but still on. Brakes don't look bad. Any ideas?

Looking for a tuner in el paso or southern NM area? Just bought the car but want to check the tune that previous owner had put on for piece of mind. Was told about THR mustang performance, anyone have any feedback or any other tuners in this area. Car is not crazy but with exhaust mac cold...

Picked up my 03 DSG yesterday. On the drive back from Oklahoma city it thru the p0171 and p0174 codes? isin't this the part throttle lean codes? thinking may be a vacumm leak, any suggestion on where to look? Car does have magnaflow exhaust, cold air and 2.81 pulley and tune. Didn't put it...

Picked up the 03 and drove it back. Traded in my 98 BAB in Oklahoma City, if anyone is looking for a clean fairly stock 98 BAB with 44,000 original miles it is at the toyota dealership in Oklahoma city, just passing along in case anyone is looking for a clean 98. couple of pics of the 03...